Triple Hydraulic Gear Pump For Feida And MKD Water Well Drilling Rigs

1 / 7
Parameter Specification
Pump type Triple-section external gear pump
Feida FY260 (Quanchai engine) 40 + 40 + 20 cm³/rev
Feida FY450 (reviewed build) 63 + 63 + 32 cm³/rev
MKD fitment Matched by original pump code and mounting check
Product Information

Triple Hydraulic Gear Pump for Feida and MKD Water Well Drilling Rigs

This water well drilling rig hydraulic pump is a three-section gear pump for replacement enquiries on Feida FY260, FY450 and MKD rigs, subject to pump-code and installation checks.

Each section feeds its own circuit from a single shaft. On a triple pump, displacement per section is what decides fitment. The Feida FY260 Quanchai engine build runs 40 + 40 + 20 cm³/rev. The reviewed FY450 build runs 63 + 63 + 32 cm³/rev. A pump with the wrong split can bolt on and still underfeed one circuit, so matching starts from the rig configuration and the original pump code, not from the catalogue.

40+40+20cc

Feida FY260 Quanchai build, per section

63+63+32cc

Feida FY450 reviewed build, per section

What a Triple Gear Pump Does on Feida FY260 and FY450 Drilling Rigs

On a Feida water well rig, the three pump sections typically supply separate circuits, such as rotation, feed and auxiliary functions like mast raising or rod handling. The FY260 Quanchai build and the reviewed FY450 build each use their own displacement combination. Actual values depend on how the rig was configured at the factory, and a later engine or pump swap can change them. Confirm the installed configuration before ordering a replacement.

Feida FY260 / FY450 Triple Gear Pump Displacement per Section

Verified builds are listed separately from reference combinations and supplier part numbers.

Values depend on the rig build.

Configuration Displacement per section (cm³/rev) Status
Feida FY260, Quanchai engine 40 + 40 + 20 Verified build
Feida FY450 63 + 63 + 32 Reviewed build
Reference combinations 35+35+20, 40+40+25, 45+40+20, 50+50+25 Reference only
CBGJ2040/2040/2025 40 + 40 + 25 Supplier reference, not a verified OEM cross-reference
CBGJ2050/2050/2025 50 + 50 + 25 Supplier reference, not a verified OEM cross-reference

Replacing an MKD Drill Rig Hydraulic Pump: Start with the Original Pump Code

This page gives no fixed displacement for MKD rigs. Pump displacement and interfaces on MKD drill rigs vary widely between models. We match replacements against the original product code, the rig model and the equipment details, then check mounting dimensions against the existing pump.

Water Well Drilling Rig Hydraulic Pump Replacement Checklist

These details confirm each section's displacement and the mounting interface before quoting.

  1. 01

    Nameplate photo

    Send a clear photo of the original pump nameplate. It usually carries the assembly code that defines section sizes.

  2. 02

    Rig and engine

    State the rig model and the engine make and model, for example FY260 with a Quanchai engine.

  3. 03

    Shaft data

    Give the spline specification and the shaft-end rotation direction, viewed from the shaft end.

  4. 04

    Mounting interface

    Measure the pilot diameter and bolt spacing, and note the port layout on each section.

  5. 05

    Operating conditions

    Add the drive speed and working pressure. These figures are used to check that the section sizes suit the duty.

Feida and MKD Triple Gear Pump Questions

Can a CBGJ2040/2040/2025 or CBGJ2050/2050/2025 pump replace the original directly?
Not without verification. Both are supplier references, not confirmed OEM cross-references. Shaft, pilot, bolt spacing and ports must be checked against your original pump.
Can I order one of the reference displacement combinations?
Yes, once the rig configuration is confirmed. The reference sets cover common builds, but the section sizes must match your rig and engine.
The nameplate is missing. Can the pump still be matched?
Usually, yes. Send the rig model and serial plate, the engine model, and photos of the shaft, flange and ports with measured pilot diameter and bolt spacing.
How are inspection items and documents agreed?
They are agreed in the quotation. Dimensional checks and leak inspection are typical, and pressure and flow testing applies where relevant. Shipping documents are listed alongside these checks.

Request a Quote for a Feida or MKD Triple Hydraulic Gear Pump

Send the original pump code or nameplate photo, rig and engine model, measured mounting dimensions, and quantity so Olive Branch Hydraulics can check the configuration and quote.

Send Pump Code for a Quote

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.