SJ21032 SJ16699 TA14593 Tandem Gear Pump For John Deere Tractors

1 / 4
Parameter Specification
Part number SJ21032; cross-ref SJ16699, TA14593 (version check)
Type Two-section external gear pump, side ports
Reference displacement 31 + 15 cm³/rev
Reference pressure 20 MPa rated / 25 MPa max
Reference speed 1500 rpm rated / 2500 rpm max
Reference rotation CCW viewed from drive end
Drive / mounting 1:8 taper, 5/8-18UNF-2A, Ø101.6 mm pilot
Customization Private marking, custom packaging, sample-based tooling
Trade term EXW Hebei, China
Configuration check Drawing reference; supplied version agreed against sample.
Product Information

SJ21032 Tandem Gear Pump for John Deere 6B and 6E Tractors (SJ16699 / TA14593 Cross-Reference)

The SJ21032 tandem gear pump fits a John Deere 6B or 6E tractor only after the tractor serial number, rotation, shaft and port layout are checked against the dimensioned drawing.

The tractor model name alone does not settle the fit. Suppliers list SJ16699 and TA14593 against the same tractors, but these are supplier cross-references and can belong to different machine versions. The reference configuration is a two-section external gear pump with 31 + 15 cm³/rev displacement, 20 MPa rated pressure, a 1:8 tapered keyed shaft and counterclockwise rotation viewed from the drive end.

We manufacture the pump in Hebei, China. The supplied version is agreed against your sample or drawing before production, so shaft, pilot, mounting centres and ports are confirmed in writing first. John Deere model names on this page are application references only. This is not a genuine John Deere part.

  • Part number — SJ21032. Supplier cross-references SJ16699 and TA14593 need version confirmation.
  • Related enquiry — RE241578 appears in supplier search lists. It is a distinct OEM main-pump reference, and an identical assembly is not confirmed.

31 + 15cc

Displacement per revolution

20 / 25MPa

Rated / maximum pressure

Send Serial Number for Matching

SJ21032 Tandem Gear Pump Overview

The SJ21032 combines a 31 cm³/rev section and a 15 cm³/rev section on one tapered drive shaft. This gives the tractor two separate oil flows from a single mounting point. At the 1500 rpm rated speed, theoretical output is about 46.5 L/min from the larger section and 22.5 L/min from the smaller one. Actual delivery is lower because of volumetric efficiency, oil viscosity and temperature. Production follows the reference drawing and your sample, so dimensions are agreed before any parts are machined.

Key Features of the 31+15cc Tandem Gear Pump

Two sections, one drive

Two external gear sets are stacked in series and driven through a common shaft. The two circuits stay hydraulically separate. Service requirements depend on inspection of both pump sections and their shared drive.

1:8 tapered keyed shaft

The tapered shaft has a key and a 5/8-18UNF-2A end thread, which pulls the drive gear tight onto the taper. A parallel-shaft pump will not mount on this drive.

Ø101.6 mm locating pilot

The pump centres on a Ø101.6 mm pilot with 146 ±0.2 mm main mounting centres. Exact tolerances are confirmed from the drawing and your sample.

Side oil ports

Inlet and outlet ports sit on the housing sides. Port size and thread form are verified against your old pump before production.

SJ21032 Technical Specifications That Decide Fit

These values come from the ChangJia SJ21032 reference configuration. The supplied version is agreed against your sample or drawing.

Check rotation and the shaft taper before confirming the mounting and oil ports.

Displacement 31 + 15 cm³/rev
Pressure 20 MPa (200 bar) rated, 25 MPa (250 bar) maximum
Speed 1500 rpm rated, 2500 rpm maximum
Rotation Counterclockwise, viewed from drive end
Mounting / drive 146 ±0.2 mm centres, Ø101.6 mm pilot, 1:8 taper

Material and Construction of the Gear Pump Housing

The pump uses a two-section external gear design inside a green painted housing. Each section has a driving gear and a driven gear running inside a close-tolerance gear chamber. In pumps of this class, the gears are typically case-hardened steel. The housing material is confirmed against your sample, because aluminium alloy and cast iron are both common in this pressure range. Shaft geometry is fixed by the drawing: a 1:8 taper, key and 5/8-18UNF-2A thread.

How a Tandem External Gear Pump Works

When the gears rotate, oil is trapped between the gear teeth and the housing wall. It is carried around the outside of the gears from the inlet side to the outlet side. Where the teeth mesh in the centre, the oil is pushed out into the outlet port. Displacement per revolution is fixed, so flow rises in proportion to shaft speed. Pressure is set by the load in the circuit, not by the pump. The reference configuration lists 20 MPa rated and 25 MPa maximum pressure; allowable duration and duty cycle must be confirmed for the supplied unit.

Quality Control Checkpoints

  1. Drawing review

    Shaft, pilot, mounting centres and ports are checked against the SJ21032 reference drawing and your sample. Any differences are resolved in writing before production.

  2. Sample measurement

    Your old pump or sample is measured for taper, thread, port positions and rotation arrow.

  3. First-article check

    The first produced pump is measured against the agreed dimensions before batch production continues.

  4. Pre-shipment check

    Rotation marking, part marking and packing are checked against the order. If you need a test report at a specific pressure, state it in the RFQ.

John Deere Tractor Applications (Serial Number Required)

Suppliers list the following models. Confirm the serial number and hydraulic configuration for each one.

John Deere 6B series

6110B, 6120B, 6135B, 6140B and 6150B.

John Deere 6E variants

Listed by suppliers. Earlier and later builds can differ in pump configuration.

Earlier listed models

1054, 1204, 1354, 1404, 6603 and 6803.

Tractor hydraulic and steering supply

The two sections typically serve separate circuits. Check which circuit each section feeds on your tractor.

Installation Guide

  1. Confirm rotation

    Compare the arrow on the new pump with the old pump. The reference configuration is CCW viewed from the drive end.

  2. Clean the mating faces

    Clean the pilot and the taper seat. Dirt on the 1:8 taper prevents full seating.

  3. Seat and torque

    Fit the key, seat the shaft and tighten the 5/8-18UNF nut to the tractor manual value.

  4. Prime and start

    Fill the inlet side with oil, connect the side ports and run at low idle to purge air before applying load.

Maintenance and Service Life

  • Oil cleanliness

    Contaminated oil can damage gear side faces and bearing surfaces.

  • Inlet condition

    A restricted suction line causes cavitation noise and erosion.

  • Pressure discipline

    Continuous operation above 20 MPa shortens bearing and seal life.

  • Service life

    Service life depends on oil condition, duty cycle and relief valve setting. No fixed hours are stated.

How to Choose the Right SJ21032 Pump Version

  1. Read the serial number

    Send the tractor serial number. Both 6B and 6E variants appear in supplier lists.

  2. Check old pump markings

    Note the part numbers. Do not combine SJ16699, TA14593 or RE241578 without verifying the version.

  3. Measure the drive

    Measure the taper, key, thread and Ø101.6 mm pilot.

  4. Check ports and rotation

    Confirm the side port positions and the rotation arrow. Generic CW/CCW listings do not mean the pump is reversible.

Custom OEM and ODM Gear Pump Manufacturing

Production is based on your sample or drawing, with tooling developed where the version requires it.

MOQ and sampling time are stated in the quotation once tooling needs are known.

Private marking

Your part number or brand is marked on the pump, as you specify.

Custom packaging

Boxes and labels are made to your layout.

Configuration matching

Shaft, ports and rotation are built to your sample.

How custom orders work

  1. Submit

    Send your drawing, sample or serial number.

  2. Review

    We confirm dimensions and identify any tooling needs.

  3. Sample

    A sample is built and sent for your fit check.

  4. Production

    Batch production starts after you approve the sample.

Packaging and Shipping

Trade term

EXW, Hebei, China.

Packing

Neutral or private-label boxes. Carton count and weight are listed in the quotation.

Port protection

Ports are capped before packing.

MOQ and Lead Time

MOQ Per quotation · Depends on whether the order uses an existing configuration or needs new tooling
Lead time Per quotation · Confirmed after the sample is approved
Incoterm EXW · Hebei, China

Warranty and After-Sales Support

Terms

Warranty terms are written into the quotation.

Fit disputes

These are checked against the approved drawing and sample.

Records

Your agreed configuration is kept on file for repeat orders.

SJ21032 Tandem Gear Pump FAQ

Is SJ21032 identical to RE241578?
Not confirmed. RE241578 is a distinct OEM main-pump reference, so we check it as a related enquiry.
Are SJ16699 and TA14593 the same pump?
They are supplier cross-references. Each one needs version confirmation by tractor serial number.
Can the rotation be reversed?
Not by default. The reference configuration is CCW viewed from the drive end, so check the arrow on your old pump.
Is this a genuine John Deere part?
No. We manufacture it to the drawing and to your sample.
What other names is this pump listed under?
Tandem gear pump John Deere SJ21032; bomba de engranajes doble; bomba de engrenagem dupla; сдвоенный шестерённый насос; مضخة تروس مزدوجة; çift dişli pompa; pompe à engrenages double; bơm bánh răng đôi; pompa roda gigi ganda.

Request a Drawing-Matched Quote or Sample

Send your tractor serial number, photos of the old pump showing the rotation arrow and shaft, and the quantity you need. You will receive a configuration check against the SJ21032 drawing, plus pricing, MOQ and lead time.

Send Serial Number and PhotosOrder a Sample

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.