CJH3 Bidirectional Cast Iron Gear Pump 32-110 Cc With Three-Hole Flange

1 / 4
Parameter Specification
Pump type External gear pump, bidirectional, fixed displacement
Body material Cast iron
Models / displacement CJH3-32 to CJH3-110, 32-110 cc/r
Catalogue reference pressure 22/25 MPa (32-63 cc); 20/23 MPa (80-110 cc)
Catalogue reference speed 2200 / 2500 rpm
Reference ports G3/4, G1 or G1-1/4 by size
Reference mounting Three-hole flange, 3ר12, Ø73 PCD, Ø52 pilot
Drive Internal splined coupling
Customization Spline, ports, marking, private-label packaging
Product Information
CJH3 Series Gear Pump

CJH3 Bidirectional Cast Iron Gear Pump, 32-110 cc, Three-Hole Flange

The CJH3 bidirectional cast iron gear pump suits tractor and harvester hydraulic circuits that need 32 to 110 cc/rev from a three-hole flange and an internal splined drive. The 32-63 cc sizes carry a catalogue rating of 25 MPa maximum.

Seven displacements share one body family: CJH3-32, CJH3-40, CJH3-50, CJH3-63, CJH3-80, CJH3-100 and CJH3-110. Source catalogue references list 22/25 MPa rated/max for 32-63 cc and 20/23 MPa for 80-110 cc. All sizes are listed at 2200/2500 rpm. These are reference values, not a performance guarantee. Each supplied build is matched to your confirmed drawing or sample.

Olive Branch Hydraulics machines and assembles these pumps in Hebei, China. Production is in Ningjin, about 9 km from our Xinji sales office, for sample and drawing coordination. The gallery shows real product photos and a reference dimension drawing for a first interface check.

  • Mounting — Three Ø12 holes on a Ø73 PCD with a Ø52 pilot, per the reference drawing.
  • Drive — Internal splined coupling. The reference build has no external shaft.

32-110cc/r

Displacement range

25MPa

Max pressure, 32-63 cc sizes

2500rpm

Max speed, all sizes

Send Drawing for Quote

CJH3 Gear Pump Product Overview

The CJH3 is a cast iron external gear pump. The same pump body can be driven in either rotation direction. The drive enters through an internal spline, and the pump locates on a three-hole flange, which is a common interface on agricultural gearboxes and power take-off units. It is not a piston or swashplate pump. It has fixed displacement and no variable control.

We supply the full family in one listing so you can quote several sizes against a single interface. Where you already run a CJH3-type pump, we work from your sample or drawing. Other series codes are not treated as equivalent to CJH3.

Key Features of the CJH3 Pump

Each feature below is tied to how the pump is built and where its limits are.

Bidirectional rotation

The gear set and porting allow the pump to run clockwise or counter-clockwise, subject to the confirmed bidirectional configuration. The suction and pressure ports swap with rotation direction. Confirm the port function and the drain or seal arrangement on the drawing before plumbing.

Cast iron housing

The cast iron body and covers resist deflection at the 20-25 MPa reference pressures and damp gear noise. The trade-off is weight: a cast iron gear pump is typically heavier than an aluminium-body pump of similar displacement.

Three-hole flange with Ø52 pilot

The reference interface uses three Ø12 holes on a Ø73 PCD. The Ø52 pilot centres the pump on the drive housing. Your mating flange must match all three dimensions. A close PCD does not guarantee pilot fit.

Internal splined drive

The pump's drive gear carries a female spline that accepts the gearbox or PTO shaft directly. Spline count, module and length have to match your drive. Send the spline data or a sample with your enquiry.

CJH3-32 to CJH3-110 Specifications by Model

Displacement sets the flow. The pressure band and port size then follow from the model you choose.

All sizes reference 2200 rpm rated and 2500 rpm max. Theoretical flow equals displacement × speed. For example, a CJH3-63 at 2200 rpm gives 138.6 L/min before volumetric losses. These are source catalogue references and are confirmed against your drawing at quotation.

Model Displacement (cc/r) Rated / Max Pressure (MPa) Port
CJH3-32 32 22 / 25 G3/4
CJH3-40 40 22 / 25 G3/4
CJH3-50 50 22 / 25 G1
CJH3-63 63 22 / 25 G1
CJH3-80 80 20 / 23 G1
CJH3-100 100 20 / 23 G1-1/4
CJH3-110 110 20 / 23 G1-1/4

Material and Construction

Housing and Covers

The body and end covers are cast iron. Machining covers the gear bores, the Ø52 pilot, the three Ø12 mounting holes and the threaded ports. Housing dimensions and material specification are confirmed for the required pressure duty. This matters at the 22-25 MPa ratings of the smaller sizes. Port threads follow the G-series sizes listed for each model unless your drawing specifies otherwise.

Gears, Side Plates and Seals

Gear pumps of this class typically use hardened steel gears running between side plates or bushings. Pressure on the side plates controls end clearance as pressure rises. Seal compound compatibility must be confirmed for the specified hydraulic fluid. If your system runs hotter or uses different fluids, state the oil type and temperature range so the seal material can be confirmed on the drawing.

How a Bidirectional Cast Iron Gear Pump Works

Two meshing gears turn inside close-fitting bores. Oil fills the tooth spaces on the suction side and is carried around the outer edge of the gears to the pressure side. Where the teeth mesh in the centre, the oil is pushed out and cannot flow back to suction. Output is fixed per revolution, so flow changes only with drive speed.

In a bidirectional pump, reversing the rotation reverses which port draws oil and which delivers it. Leakage paths are typically drained internally through check valves or to an external drain so that the seal never sees full pressure in either direction. Which method your build uses is shown on the drawing. Verify it against your circuit before installation.

Quality Control Process

Inspection points follow the confirmed drawing, not a generic checklist.

  1. Incoming castings

    Cast iron housings and covers are checked for porosity, cracks and machining allowance before they are released to machining.

  2. Machined dimensions

    Gear bores, Ø52 pilot, Ø73 PCD hole positions and port threads are gauged against the drawing for your build.

  3. Gear set and clearances

    Gear width and end clearance are checked during assembly. These clearances govern volumetric efficiency and internal leakage.

  4. Functional test

    The pressure, flow and leakage test scope, and the acceptance values, are set per order on the drawing or inspection sheet.

  5. Pre-shipment check

    Marking, rotation, port caps and packing are checked against the purchase order. Any required inspection records and batch marking are agreed with the order.

Tractor and Harvester Pump Applications

Any fit depends on a matching flange, spline, ports and duty cycle. No specific vehicle fit is claimed.

Tractor hitch and loader circuits

Choose displacement from the required lift flow and available drive speed, then confirm the mounting interface.

Combine and forage harvesters

Header, reel or unloading circuits can be assessed against their required flow, pressure and drive interface.

Towed implements

Pumps driven from a gearbox with a three-hole mount, where bidirectional rotation simplifies stocking.

General agricultural machinery

Fixed-displacement supply for open-centre circuits within the rated speed band.

Installation Guide

  1. Confirm rotation and ports

    Identify the suction and pressure ports for your drive direction from the drawing, and check the drain arrangement.

  2. Check the interface

    Inspect the spline, the Ø52 pilot and the flange face for burrs or damage. Lightly lubricate the spline.

  3. Mount square

    Engage the spline without forcing it. Seat the pilot fully and tighten the approved mounting fasteners evenly through the three Ø12 mounting holes.

  4. Connect lines

    Use suction lines at least as large as the inlet port. Undersized inlets typically cause cavitation and noise.

  5. Prime and start

    Fill the pump with clean oil and start at low speed without load. Bleed air before building pressure.

Maintenance and Service Life

Oil cleanliness

Agree the oil cleanliness and filtration requirement for the supplied pump. Contamination can damage gears, bearings and sealing faces.

Viscosity and temperature

Run within the oil supplier's viscosity range. Thin, hot oil raises internal leakage.

Duty cycle

Service life depends on pressure, speed and cleanliness. Running continuously at maximum pressure shortens it.

Spares

Seal kits can be quoted with the pump order for field servicing.

How to Choose the Right CJH3 Model

Check both the drive interface and operating displacement.

Common enquiry terms include CJH3-63 gear pump, three hole hydraulic pump, bomba de engranajes CJH3-63 hierro fundido, bomba de engrenagem CJH3-80 ferro fundido, шестерённый насос CJH3-50 чугунный, مضخة تروس CJH3-100 حديد زهر, CJH3-40 dişli pompa döküm, pompe à engrenages CJH3-110 en fonte, bơm bánh răng CJH3-32 gang and pompa gear CJH3-63 besi cor.

  1. Set flow

    Divide the required L/min by the drive speed in rpm, multiply by 1000, then allow for volumetric losses.

  2. Check pressure

    Match the continuous duty and relief setting to the confirmed rated pressure; maximum pressure is not a continuous-duty rating.

  3. Match interface

    Compare the three Ø12 holes, Ø73 PCD and Ø52 pilot with your flange.

  4. Define the drive

    Send the spline data or a sample, along with the rotation direction.

  5. Confirm ports

    Use G3/4, G1 or G1-1/4 by size, or specify alternatives on your drawing.

OEM, ODM and Private-Label CJH3 Pumps

Customization is available whether you start from a sample pump or from a new drawing.

Interface

Spline, pilot, flange and port threads can be adjusted to your drawing.

Sample duplication

Your existing pump is measured and reproduced, and you sign off the drawing before production.

New tooling

New castings or fixtures can be made where your design differs from the reference family.

Private label

Your logo, nameplate, part numbers, barcode labels and branded cartons. Customer drawings and brand files can be covered by an NDA.

How custom orders run

  1. Requirement

    You send a drawing, sample or specification, with quantity.

  2. Sample

    A sample is built to the agreed drawing.

  3. Confirmation

    You test the sample and approve the drawing.

  4. Production

    Bulk production follows the approved sample.

  5. Delivery

    Goods are inspected, packed and released on the agreed Incoterm.

Packaging and Shipping

Base term

EXW Hebei, China. Other Incoterms can be discussed in the quotation.

Protection

Ports are plugged and machined faces protected against rust for transit.

Cartons

Carton size, weight and pieces per carton depend on the model mix and are stated in the quotation.

Branded packing

Neutral or private-label cartons with your labels are available.

MOQ and Lead Time

Commercial terms are fixed in the quotation, based on your build and volume.

MOQ Per model and build · Confirmed for the selected build and tooling requirement
Sample Available · Sample cost and timing quoted per drawing
Lead time Per order quantity · Based on first-order quantity or annual volume
Pricing Tiered by quantity · Volume breaks set out for distributors
Incoterms EXW Hebei · Other terms on request

Warranty and After-Sales Support

Warranty terms

Coverage scope and duration are stated in the quotation for each order.

Failure review

Send photos, the operating conditions and the batch marking, and we will carry out a cause analysis.

Traceability

Specify any required batch marking and inspection documents in the order.

Spares

Seal kits and matching pumps can be quoted for repeat orders.

CJH3 Gear Pump FAQ

Is the CJH3 a piston pump?
No. It is a fixed-displacement external gear pump with a cast iron body. It has no swashplate and no variable control.
Can you reproduce the CJH3 pump we already use?
Yes. We work from your sample or drawing, measure the interface and spline, and you approve the drawing before production.
Will it fit our tractor model?
Fit depends on the interface, not the vehicle name. Send the flange, spline, port and rotation details, and we will check them against our drawing.
What are the MOQ and lead time?
Both are set in the quotation. They depend on the model, whether new tooling is needed, and your first-order quantity or annual volume.
Are the listed pressures and speeds guaranteed?
They are source catalogue references. The supplied build and your application are checked against your sample or drawing.

Get a CJH3 Quote or Sample

Send us the model or displacement, the rotation direction, your spline data or a drawing or photo, and your first-order quantity or annual volume. We will reply with an EXW Hebei quotation, a sample option and a lead time based on that quantity.

Send Drawing and QuantityRequest a Sample

Drawing, photo or sample accepted, Mixed sizes in one enquiry, Private-label packing quoted on request

Ordering references

Model Displacement Flow Also written as Max rpm
CJH3-32 32 cc/rev 70.4 L/min CJH3 32, CJH332 2,500
CJH3-40 40 cc/rev 88 L/min CJH3 40, CJH340 2,500
CJH3-50 50 cc/rev 110 L/min CJH3 50, CJH350 2,500
CJH3-63 63 cc/rev 138.6 L/min CJH3 63, CJH363 2,500
CJH3-80 80 cc/rev 176 L/min CJH3 80, CJH380 2,500
CJH3-100 100 cc/rev 220 L/min CJH3 100, CJH3100 2,500
CJH3-110 110 cc/rev 242 L/min CJH3 110, CJH3110 2,500

Flow is theoretical at 2,200 rpm. Spaced and unhyphenated entries are writing variants, not additional manufacturer material numbers. Confirm any nameplate or OEM number against the supplied sample.

 

You May Also Like

Related Articles

Can A Gear Pump Be Reversed?

Discover if gear pumps can safely run in reverse. Learn about bidirectional operation, seal design, and key tr…

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.