9510080104 83282000 AZPF-11-002RAXXXMB-S0440 Gear Pump For Valmet

Parameter Specification
Model reference 9510080104
Type cross-reference AZPF-11-002RAXXXMB-S0440
OEM reference 83282000 (832 820 00)
Catalogue fitment Valmet 685 / 785 4x2, 4x4, BF65, BF75HT
Pump type Single-section gear pump, aluminium body
Mounting flange Black two-hole elongated flange
Drive shaft Cylindrical keyed shaft
Port Side threaded port, blue protective plug
Displacement / pressure / rotation Confirmed from pump plate or sample
Customization Sample matching, new tooling, private-label packaging
MOQ / lead time Stated on quotation per build, EXW Hebei
Product Information
Catalogue-referenced build

9510080104 83282000 Hydraulic Gear Pump for Valmet 685 785 BF65 BF75HT

This 9510080104 / 83282000 hydraulic gear pump should not be ordered from the part number alone. It suits Valtra/Valmet 685, 785, BF65 and BF75HT HIC-Trac circuits once the old pump plate or a sample confirms the build.

Confirm the fitted pump configuration against the nameplate, drive interface and operating conditions before ordering. The unit shown is a China-made single aluminium-body gear pump. It has a black two-hole elongated flange, a cylindrical keyed drive shaft and a side threaded port sealed with a blue protective plug.

We manufacture this agricultural keyed shaft gear pump in Hebei, China. Each order is matched to your pump plate, sample or drawing before production. The product photo shows the reference version. A matching dimension drawing is not currently included; interface dimensions must be confirmed against your sample.

  • Reference pair — Model reference 9510080104 with OEM reference 83282000, also written 832 820 00.
  • Sales and production — Our sales office in Xinji and our production site in Ningjin, Hebei, are about 9 km apart.
  • Order basis — Builds are made from a supplied sample or drawing. New tooling and private-label packaging are available.

Send pump plate photo

Product Overview: Hydraulic Gear Pump 9510080104 / 83282000

The Bosch Rexroth agriculture catalogue FL-BRM-0243, page 28, links the pair 9510080104 and 83282000 to six machine entries: Valtra/Valmet 685 4x2, 685 4x4, 785 4x2, 785 4x4, BF65 and BF75HT, with the HIC-Trac function. Olive Branch Hydraulics manufactures this pump in China under its own production. Third-party brand names on this page only identify the equipment and the catalogue reference. They do not indicate an original part from those brands.

Catalogue reference 9511089181 is an associated assembly or component number and is not an alias for the complete pump. Part number 9510080102 and the related seal kits are separate items. They are quoted separately.

Key Features of the 9510080104 Gear Pump

These are the physical features of the reference build that you can check against the pump on your machine.

  • Aluminium single-section body

    The reference unit is a single gear section in an aluminium housing. It is lighter than cast-iron bodies of similar size. The actual pressure and speed limits must be confirmed for the selected construction.

  • Two-hole elongated flange

    The black-finished flange has two bolt holes on an elongated pattern. Measure the hole centre distance and the pilot diameter on your old pump, because flanges that look alike can differ by a few millimetres.

  • Cylindrical keyed shaft

    The drive is a parallel shaft with a key, not a spline. Shaft diameter, key width and shaft length are measured from your sample before machining starts.

  • Side threaded port

    The port is threaded on the side of the body and arrives sealed with a blue protective plug. Confirm thread type, size and sealing method against your hose fittings.

Technical Specifications and How to Match the Pump

Confirm the drive, mounting, ports and hydraulic operating requirements against the fitted pump and circuit.

Displacement, rated pressure, permissible speed and rotation are confirmed for the supplied configuration before production.

Model / OEM reference 9510080104 / 83282000 (832 820 00)
Pump type Single-section external gear pump, aluminium body
Mounting Two-hole elongated flange, black finish
Drive Cylindrical keyed shaft
Displacement (cc/rev) Read from pump plate or measured from sample
Rotation and max. pressure Confirmed from plate, sample and circuit duty

Material and Construction

The housing is aluminium, and the flange carries a black finish. The gear pair and shaft are typically made from hardened steel. They run in bushings or bearing plates that set the side clearance against the gear faces. That side clearance largely determines volumetric efficiency, so the bushing material and its fit are checked against the sample when it is matched.

A lip-type shaft seal is typical for this kind of keyed-shaft pump. The seal material is selected for mineral-based tractor transmission or hydraulic oil. If your machine runs a different fluid, state it in your enquiry so the seal compound can be chosen to suit.

How Does an External Gear Pump Work?

Two meshing gears turn inside the housing. Oil is carried around the outside of each gear, in the spaces between the teeth and the housing wall. Where the teeth mesh again, the oil is pushed out through the pressure port. The output per revolution is fixed by the gear width and tooth geometry, so flow rises in direct proportion to shaft speed.

The pump does not create pressure on its own. Pressure builds from the load and is capped by the circuit relief valve. This is why the relief setting of the HIC-Trac circuit has to be known before the pump's rated pressure can be confirmed.

A pump rated below the relief valve setting will wear quickly, even when the flange and shaft fit perfectly.

Quality Control Process

Every check is made against the sample or drawing you approved, not against a generic catalogue figure.

  1. Incoming parts

    Housings, gears and shafts are inspected for size on the bores, gear width and shaft diameter before assembly.

  2. Machining check

    Flange hole spacing, pilot diameter, keyway and port thread are gauged against the confirmed sample.

  3. Assembly

    Bushings, seals and gears are fitted to the clearances defined for this build. Shaft rotation is checked against the confirmed direction.

  4. Run test

    The required pressure, flow and leakage checks and acceptance values are agreed for the confirmed configuration.

  5. Release

    Ports are plugged, and the unit is labelled with the agreed part reference before packing.

Application Scenarios

These applications come from the FL-BRM-0243 catalogue. The variant fitted to each machine still has to be checked before installation.

Valmet 685 4x2 / 4x4

Catalogue-listed for the HIC-Trac hydraulic function. Check the plate on the fitted pump, because rebuilt tractors may carry a different variant.

Valmet 785 4x2 / 4x4

Same reference pair in the catalogue. Compare the flange pattern and shaft key against the removed pump.

BF65 and BF75HT

Catalogue entries for the same pump pair. Confirm the port thread before ordering hoses or adapters.

Distributor and workshop stock

Distributors and workshops can specify the required reference, interface dimensions and stock quantity in one enquiry.

Installation Guide

  1. Verify the variant

    Compare the plate, flange, keyed shaft and port with the removed pump before you open the circuit.

  2. Clean the circuit

    Drain and flush contaminated oil, and replace the suction filter. Debris left behind from the old pump will damage the new gears.

  3. Fit and align

    Install the key, then engage the drive without forcing it. Torque the two flange bolts evenly to the tractor manufacturer's value.

  4. Prime and start

    Fill the pump with clean oil through the inlet and start at low idle. Check the ports and the shaft seal for leaks before you put the circuit under load.

Maintenance and Service Life

Oil cleanliness

Follow the agreed oil cleanliness, filtration and oil change requirements for the operating duty.

Suction side

A blocked suction filter or a loose inlet fitting causes cavitation, which shows up as noise and pitted gears.

Relief setting

Keep the relief valve within the pump's confirmed pressure rating.

Shaft seal

Check seal condition, alignment and inlet or case pressure when shaft leakage occurs.

How to Choose the Right 9510080104 Pump: 4 Checks

1. Read the plate

Photograph the nameplate on the removed pump and send it with the 9510080104 or 83282000 reference. The plate often states displacement and rotation directly, which settles most of the matching questions in one step.

2. Measure the drive

Measure the shaft diameter, the key width and the shaft length. A keyed shaft that is off by 1 mm will not seat in the drive.

3. Check flange and port

Record the bolt hole centre distance, the pilot diameter and the port thread. These three values decide whether the pump drops straight into place or needs adapters.

4. State the duty

Give us the relief valve setting and the engine speed at the pump. With these, displacement and pressure rating can be confirmed for your circuit rather than assumed from a listing.

OEM and ODM Customization

Builds can be duplicated from a sample, or produced from new tooling to your drawing.

Sample-based duplication

We measure your pump and machine to match its flange, shaft and porting.

New tooling

New tooling covers housings or flanges that no existing tooling covers. Tooling cost and timing are quoted separately.

Private label

Your logo, part number, barcode labels and printed cartons can be applied. Drawings and brand files are used only for your orders, and an NDA can be signed on request.

How custom orders work

  1. Requirement

    You send the sample, drawing or plate photo together with the expected quantity.

  2. Sample

    We produce a sample for you to check on the machine.

  3. Confirmation

    You approve the sample, which then becomes the reference for production.

  4. Production and delivery

    Bulk production is built and inspected to that reference, then released EXW Hebei.

Packaging and Shipping

Port protection

Each pump ships with threaded port plugs fitted.

Unit packing

Neutral or private-label cartons are available, marked with the agreed part reference.

Carton data

Carton size, weight and quantity per carton are listed on the packing list issued with the quotation.

Incoterms

Standard terms are EXW Hebei, China. Your forwarder collects the goods from our facility.

MOQ and Lead Time

Commercial terms depend on the build route and are fixed in the written quotation.

MOQ

Per quotation

Depends on whether the order uses an existing build or new tooling

Volume pricing

Quantity breaks

Shown on the quotation for distributor and wholesale volumes

Sample

Per quotation

Built to your plate, sample or drawing

Lead time

Per quotation

Confirmed after the sample is approved

Incoterms

EXW

Hebei, China

Warranty and After-sales Support

Written terms

Warranty terms are stated on the quotation and the proforma invoice.

Agreed reference

Claims are assessed against the approved sample or drawing.

Technical queries

Installation and matching questions are answered by our engineering staff.

Repeat orders

Repeat orders are built to the same confirmed reference.

FAQ

Is 9511089181 the same pump as 9510080104?
The catalogue lists 9511089181 as an associated pump component reference. It is not confirmed as an interchangeable complete-pump alias; specify the required assembly when enquiring.
Can you confirm displacement and pressure before we order?
Yes, provided you send the pump plate, a sample or your circuit duty. We do not quote figures taken from secondary listings.
Is this an original Valtra or Bosch Rexroth part?
No. Olive Branch Hydraulics manufactures it in China. The brand names on this page only identify the equipment and the catalogue reference.
Do you offer regional distribution terms?
Yes, case by case. Volume breaks, territory and marketing materials for distributors are discussed when we quote.
What do buyers call this pump in other languages?
EN hydraulic gear pump 9510080104 83282000; ES bomba hidraulica Valtra 9510080104 83282000; PT bomba hidráulica de engrenagem 9510080104 83282000; RU шестеренный гидронасос 9510080104 83282000; AR مضخة تروس هيدروليكية 9510080104 83282000; TR hidrolik dişli pompa 9510080104 83282000; FR pompe hydraulique à engrenages 9510080104 83282000; VI bơm bánh răng thủy lực 9510080104 83282000; ID pompa roda gigi hidrolik 9510080104 83282000.

Request a Quote or Sample for 9510080104

Send a photo of the pump plate or the shaft and flange measurements, your quantity and your destination market. We will reply with a matched build confirmation, sample terms and a quotation stating MOQ, lead time and price breaks.

Send pump detailsOrder a matched sample

  • Pump plate photo or sample
  • Quantity and packaging needs
  • Destination country

Part number cross-references

Item Model OEM ref Type
Role Pump model ref Valtra/Valmet OEM Full type code
Number 9510080104 83282000 AZPF-11-002RAXXXMB-S0440
Reference source Bosch p.28 Bosch p.28 Maker list
Also written as None 832 820 00 None
Status Check plate Check plate Check plate

Cross-references only. 9511089181 is an associated pump component reference, not a confirmed whole-pump interchange. Send a plate photo to confirm.

 

You May Also Like

Related Articles

Can A Gear Pump Be Reversed?

Discover if gear pumps can safely run in reverse. Learn about bidirectional operation, seal design, and key tr…

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.