3816911M91 0510765044 3800196M91 Tandem Gear Pump For Massey Ferguson

1 / 3
Parameter Specification
Reference codes 3816911M91 / 0510765044 (0510 765 044) / 3800196M91
Pump type Tandem external gear pump, two sections
Body / end covers Aluminium sections, black end covers
Drive External splined shaft, flange mount
Application MF 4200 / 4300 steering and lift, 540 PTO
Customization Private-label packaging, marking, tooled variants
MOQ Confirmed in quotation
Lead time Confirmed in quotation
Incoterm EXW Hebei, China
Product Information

3816911M91 / 0510765044 / 3800196M91 Tandem Hydraulic Gear Pump for Massey Ferguson 4200 and 4300 Series Tractors

This tandem hydraulic gear pump is listed against 3816911M91, 0510765044 (0510 765 044) and 3800196M91 for Massey Ferguson 4200 and 4300 series steering and lift circuits on 540 PTO tractors, and every order is matched to your sample or drawing before production.

It is not a generic two-section catalogue pump, and it does not cover 3816909M91, which should be quoted as a separate item. If your tractor serial falls outside the confirmed configuration, or your old pump differs in shaft, flange or port layout, the codes alone are not enough to place an order.

It fits tractors where published cross-reference catalogues link all three codes to the MF 4200 and 4300 steering and lift circuit with 540 PTO. The unit has two aluminium pump sections, black end covers, a projecting central inlet manifold, an external splined drive shaft and a mounting flange. We do not publish displacement, pressure, rotation or port thread values for this listing; each is confirmed against your sample or approved drawing.

We manufacture hydraulic gear pumps in Hebei, China, and supply this tandem unit under OEM/ODM, sample-based matching, tooling development and private-label packaging arrangements. Quotations are issued on an EXW Hebei basis.

  • Reference codes — 3816911M91, 0510765044 / 0510 765 044 and 3800196M91 are equipment and catalogue references, not our internal part numbers.
  • Matching basis — No exact corresponding drawing is held for this listing, so configuration is matched to your physical sample or confirmed drawing.

Request a matching check

Tandem Hydraulic Gear Pump for Massey Ferguson Steering and Lift: Product Overview

One drive, two independent pumping sections, two circuits.

What the unit does on the tractor

The pump supplies two separate oil flows from a single splined drive: one section serves the steering circuit and the other the lift circuit. On MF 4200 and 4300 series tractors this split keeps steering flow independent of lift demand, which is why the two sections cannot be treated as one larger pump. The listing is tied to 540 PTO builds, and the tractor serial number decides whether this exact configuration applies.

Where the value lies for a buyer

For a distributor or workshop, the risk with this part is a mismatch in shaft spline, flange pattern, port orientation or rotation, not the pump principle itself. Our process starts from your sample or confirmed drawing, so those four variables are checked before any quantity is quoted. Massey Ferguson names and part numbers are cited for identification only; the pump is produced and marked by us.

Key Features of the 3816911M91 Tandem Pump

Construction features visible on the unit and confirmed per order.

Two aluminium pump sections

Each section houses its own gear set inside an aluminium body, bolted in line on a common drive. Section sizes are matched to the sample, since steering and lift sections on tandem tractor pumps usually differ in displacement.

Projecting central inlet manifold

The inlet sits between the two sections and projects from the body, as on the reference unit. Its position and connection type are checked against the tractor's suction line, because inlet alignment must match the suction pipe.

External splined shaft and mounting flange

Drive is through an external splined shaft with a flange mount. Spline count, shaft length and flange dimensions are not standardised across tractor builds, so we gauge them from your sample rather than quoting catalogue values.

Black end covers

Both end covers carry a black finish, matching the visual layout of the reference unit. Finish colour can be altered for private-label or OEM orders without affecting the hydraulic configuration.

Technical Specifications and Cross-Reference Codes

Codes and the parameters that decide whether the pump fits; values not listed are confirmed against your sample or drawing.

Reference code 1 3816911M91
Reference code 2 0510765044 (also written 0510 765 044)
Reference code 3 3800196M91
Not covered 3816909M91 (quote separately)
Pump type Tandem external gear pump, two sections
Body / end covers Aluminium pump sections / black end covers
Drive External splined shaft, flange mount
Circuits served Steering and lift
Tractor build MF 4200 / 4300 series, 540 PTO
Displacement, pressure, rotation, port threads Confirmed against your sample or approved drawing
Supplier catalogue model 22C22/19X707 — Hydro-Pack cross-reference for 3816911M91; confirm shaft, flange and ports against the supplied sample. This is not an Olive Branch SKU.

Material and Construction

Housings, gears and shaft

The two pump sections use aluminium bodies, which keeps weight down on a pump mounted directly to the tractor drivetrain. Drive and driven gears in this pump class are typically hardened steel, running on bushings or wear plates inside each section. The external splined shaft carries drive into the first section and through to the second, so spline condition and alignment are checked on every matched sample.

Sealing and end covers

Shaft sealing on tandem gear pumps is usually a lip seal at the drive end, with O-rings between sections and at the end covers. Seal materials and kit contents are listed in the quotation rather than assumed, because fluid type and operating temperature on older tractors vary. The black end covers close each section and carry the outlet porting confirmed during matching.

How a Tandem Hydraulic Gear Pump Works

Flow generation in each section

In an external gear pump, oil enters the inlet side, is trapped between the gear teeth and the housing wall, and is carried round to the outlet side as the gears rotate. Output per revolution is fixed by the gear geometry, so flow rises in proportion to drive speed. The pump creates flow, not pressure; pressure builds from the load and is limited by the relief valve in the tractor circuit.

Two sections on one shaft

In the tandem layout, a single shaft drives both gear sets, and the central inlet manifold usually feeds both sections from one suction line. Each section delivers to its own outlet, so steering and lift receive separate flows sized by their own gear width. Wear or an incorrect section size can affect the associated circuit; diagnosis should also check the shared drive and inlet.

Quality Control and Inspection Scope

The inspection scope is agreed per order and stated in the quotation; only agreed checks are reported.

  1. Configuration matching

    Your sample or drawing is measured for shaft spline, flange pattern, inlet position, outlet ports and rotation. A matching record is returned for your approval before production.

  2. Incoming parts

    Castings, gears and seals are checked against the approved configuration. Deviations are resolved before machining or assembly continues.

  3. In-process checks

    Critical fits such as shaft, bushings and section interfaces are checked during assembly. Check points follow the agreed inspection plan.

  4. Final inspection

    Agreed items such as dimensional check, visual inspection, marking and, where agreed, running or leak checks are performed. Results go into an inspection report for your batch.

  5. Pre-shipment

    Packing, labelling and quantities are verified against the order, and photos can be supplied before release.

Which Massey Ferguson Tractors Use This Pump?

Models confirmed for reference; the exact machine serial must still match.

MF 4200 series

4215, 4220, 4225, 4225HV, 4235, 4235HV, 4240, 4245, 4245HV, 4255, 4255HV, 4260, 4265.

MF 4300 series

4315, 4320, 4325, 4325HV, 4335, 4335HV, 4345, 4345HV, 4355, 4355HV, 4365.

Steering circuit

One section supplies power steering flow, independent of lift demand.

Lift circuit

The second section supplies the three-point linkage and lift hydraulics.

PTO configuration

Referenced for 540 PTO builds; confirm PTO and serial before ordering.

Workshop and dealer stock

Suited to distributors holding pumps for MF 4200 and 4300 fleets once the configuration is confirmed.

Installation Guide for MF 4200 / 4300 Tandem Pumps

Follow the tractor's workshop manual; these steps cover the checks specific to a tandem pump.

  1. Make the tractor safe

    Lower all implements, stop the engine and relieve hydraulic pressure before opening any line. Clean the pump area to keep dirt out of open ports.

  2. Compare old and new pumps

    Lay both units side by side and check spline, flange, inlet position, outlet ports and rotation. Do not fit if any item differs.

  3. Fit seals and mount

    Use new O-rings and a clean flange face, engage the spline without forcing, and tighten fasteners to the tractor manual values.

  4. Connect and fill

    Reconnect suction and both outlets, check filter condition and fill with the fluid grade specified for the tractor.

  5. Start and check

    Run at idle, cycle steering and lift slowly, and watch for leaks, noise or air in the steering. Stop if the pump whines or flow is erratic.

Maintenance and Service Life

Service life depends mainly on fluid cleanliness, suction condition and duty cycle.

Fluid and filters

Use the fluid grade and change intervals in the tractor operator manual; contaminated oil is a common cause of gear and bushing wear.

Suction side

Check inlet hoses and clamps; air drawn in at the central inlet can cause aeration and noise.

Warning signs

Rising noise, slow steering or slow lift usually indicate wear in one section and should be checked before further use.

Shaft and spline

Inspect the drive spline at each pump removal; a worn mating spline shortens the life of a new pump.

How to Choose the Right Tandem Gear Pump

Six checks before you request a price.

  1. Tractor model and serial

    Record the model and full serial number; the code listing applies only where the serial matches.

  2. PTO configuration

    Confirm the tractor is a 540 PTO build, as the reference listing specifies.

  3. Nameplate codes

    Read the codes on the old pump and confirm 3816911M91, 0510765044 or 3800196M91; quote 3816909M91 separately.

  4. Physical details

    Photograph the shaft spline, flange, inlet, outlet ports and section lengths, or send a sample.

  5. Order route

    Choose a standard matched build for wholesale stock, private-label packaging under your brand, or OEM/ODM tooling for a modified variant.

  6. Documents and inspection

    State your target market and any document requirements, plus the inspection items you need reported.

OEM, ODM and Private-Label Options

Configuration, marking and packaging can be built around your brand and drawings.

Private-label packaging

Your logo, colour boxes, barcode labels and carton marks applied to the matched pump.

Marking and finish

Nameplate content and end-cover finish adjusted to your brand standard.

Tooled variants

Tooling developed where your drawing calls for a different flange, port or section configuration.

Confidentiality

NDA terms can be agreed before drawings or customer data are shared.

How custom orders work

  1. Requirement

    Send drawing, sample, codes, quantity and branding needs.

  2. Matching and tooling

    We confirm configuration and, if needed, quote tooling.

  3. Sample

    A sample is produced for fit and inspection on your side.

  4. Approval and production

    Production starts after written sample approval; MOQ and lead time are stated in the quotation.

  5. Delivery

    Goods are packed to your label specification and released EXW Hebei.

Packaging and Shipping

Port and shaft protection

Open ports are plugged and the spline protected before boxing; method stated in the quotation.

Unit packing

Neutral or private-label boxes, with barcode labels to your format.

Carton data

Carton size, units per carton and gross weight are given on the packing list issued with the quotation.

Incoterm

EXW Hebei, China; your forwarder arranges sea, air or consolidated freight.

MOQ, Pricing Tiers and Lead Time

All commercial terms are fixed in the written quotation for your configuration.

MOQ

Per quotation

Differs for matched standard builds, private label and tooled variants

Price structure

Quantity-break tiers

Tier levels set out in the quotation for distributors and stockists

Lead time

Per quotation

Depends on configuration, tooling and order size

Samples

Per quotation

Sample terms confirmed with the matching record

Incoterm

EXW

Hebei, China

Payment

Per quotation

Agreed before order confirmation

Warranty and After-Sales Support

  • Warranty terms

    Warranty duration and conditions are written into the quotation for each order.

  • Claim handling

    Claims are reviewed with photos, the tractor serial, fitting details and the batch marking.

  • Batch marking

    Batch references can be agreed so a claim traces back to a production lot.

  • Technical queries

    Fitting and matching questions are answered against the approved configuration record.

FAQ: 3816911M91 Tandem Hydraulic Gear Pump

Do 3816911M91, 0510765044 and 3800196M91 all refer to this pump?
Yes, published cross-reference catalogues link all three codes to the MF 4200 and 4300 steering and lift pump with 540 PTO. They are reference codes, not our part numbers. The tractor serial must still match.
Is 3816909M91 the same pump?
No, 3816909M91 is not covered by this listing. Send it as a separate enquiry with a sample or photos.
Can you give displacement and pressure figures?
Not from the codes alone. No exact corresponding drawing is held for this listing, so displacement, rotation, ports and spline are confirmed from your sample or drawing and stated in the matching record.
Can I order small quantities under my own brand?
Yes, private-label packaging is available. The MOQ for branded orders is set in the quotation according to configuration and packaging.
What terms should I use when enquiring in other languages?
Quote the codes 3816911M91, 0510765044 / 0510 765 044 and 3800196M91 with the local term. Spanish: bomba de engranajes tándem; Portuguese: bomba de engrenagens tandem; Russian: тандемный шестерённый насос; Arabic: مضخة تروس مزدوجة; Turkish: tandem dişli pompa; French: pompe à engrenages tandem; Vietnamese: bơm bánh răng đôi; Indonesian: pompa roda gigi tandem.

Send Your Tractor Serial for a Matching Check and Quotation

Send the tractor model and serial, the codes on your old pump, photos of shaft, flange and ports (or a sample), quantity, and your target market with any document requirements. You receive a configuration match, a quotation with MOQ, price tiers and lead time, and a list of the documents we can supply for that market.

  • Codes or photos are enough to start
  • Private label and OEM requests in the same enquiry

Request a matching checkAsk about a sample

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.