N150-601100-000 Forklift Hydraulic Gear Pump

1 / 4
Parameter Specification
Hangcha part / material code N150-601100-000 / 70022993
Aftermarket cross-reference 25A32X801-6
Displacement 32 cm³/rev
Drive shaft 6 splines, Ø20 mm major diameter
Rotation Counterclockwise, viewed from shaft end
Rear port threads Inlet G 1″, outlet G 1/2″
Mounting Two-slot flange; verify pilot and slot spacing
MOQ / lead time (stocked) 1 piece / 3–5 business days
Warranty One year
Product Information

Six-spline, counterclockwise, 32 cm³/rev, matched by code before it ships

This forklift hydraulic gear pump replacement displaces 32 cm³/rev through a six-spline Ø20 mm shaft, the reference configuration behind Hangcha part N150-601100-000 (material code 70022993).

Displacement sets lift speed. At 2,000 rpm, a 32 cm³/rev pump moves a theoretical 64 L/min (about 17 US gal/min) before volumetric losses. A pump with a different displacement makes the mast lift faster or slower than the truck's controller and relief settings expect. That is why the number on the nameplate matters as much as the part code.

The unit follows the Xinchai six-spline reference configuration and cross-references aftermarket code 25A32X801-6. Typical uses are electric forklift lift circuits in warehouses and logistics centres, workshop repairs, and distributor stock for worn or leaking lift pumps. Each of these applies only when the shaft, rotation, port threads and flange of the original pump match this unit.

Check My Part Number

Selecting a Forklift Hydraulic Gear Pump Replacement: Shaft, Rotation, Ports and Mounting

Start from the code, then confirm the dimensions

A part number narrows the search but does not settle it. We cross-match Hangcha part number N150-601100-000, material code 70022993 and aftermarket reference 25A32X801-6. We then check each code against the physical interface: six-spline Ø20 mm shaft, counterclockwise rotation viewed from the shaft end, G 1″ inlet and G 1/2″ outlet at the rear, flange pilot diameter and slot centre spacing, and 32 cm³/rev displacement. Two pumps can share a housing size and still differ on one of these points.

Why one mismatch is enough

A pump turned the wrong way swaps its suction and pressure sides. This typically starves the pump and can blow the shaft seal. If the spline count or major diameter is different, the pump will not engage the motor coupling. Mismatched G threads need adapters, and each adapter is another leak point. If the pilot diameter or slot spacing is off, the shaft sits out of line and loads the bearings. Brand names and model numbers are given for replacement identification only. Compatibility depends on the complete assembly code.

N150-601100-000 Gear Pump Data: Hangcha Codes, 32 cm³/rev Displacement and Six-Spline Shaft

These are the reference configuration values. Before we quote, the mounting interface is confirmed against your original pump.

Xinchai six-spline reference configuration

Specification

N150-601100-000

Hangcha part number

70022993

Hangcha material code

25A32X801-6

Aftermarket cross-reference

Full specification

Specification Xinchai six-spline reference configuration
Hangcha part number N150-601100-000
Hangcha material code 70022993
Aftermarket cross-reference 25A32X801-6
Displacement 32 cm³/rev (approx. 1.95 in³/rev)
Drive shaft 6 splines, Ø20 mm major diameter
Direction of rotation Counterclockwise, viewed from the shaft end
Rear inlet thread G 1″
Rear outlet thread G 1/2″
Mounting Two-slot flange; verify pilot diameter and slot centre spacing against the original pump

Which Electric Forklifts and Repair Jobs This Hangcha Lift Pump Suits, and When to Choose Another

This is a like-for-like lift-pump replacement, not a conversion part. It suits electric forklifts whose lift circuit uses the Xinchai six-spline reference configuration. It covers planned replacement in warehouse and logistics fleets, emergency repair of a leaking or worn pump, and parts stock for distributors serving those trucks. The fit stops at the first interface that does not match. If the old nameplate or your measurements disagree with the reference values, match a different pump from the original code. Do not modify this one to fit.

  • The original code reads N150-601100-000, 70022993 or 25A32X801-6
  • Shaft has 6 splines at Ø20 mm and rotation is counterclockwise
  • Rear ports are G 1″ inlet and G 1/2″ outlet with a two-slot flange
  • The original turns clockwise viewed from the shaft end
  • Spline count or shaft diameter differs
  • Port threads, pilot diameter or slot spacing differ from the original

Matching Your Old Pump by Part Number, Material Code and Forklift Model

We cross-check your codes and equipment data before any price is issued.

  1. Send the original code

    Give us N150-601100-000, 70022993, 25A32X801-6 or the code on your nameplate. We can work from partial codes, but the check takes longer.

  2. Add forklift and equipment details

    Send the truck make, model and serial number or year, plus the pump's position in the circuit.

  3. Send photos and key dimensions

    Send photos of the nameplate, shaft end, rear ports and flange. Include spline count, shaft diameter and slot spacing if you can measure them.

  4. Receive the confirmed match

    We confirm the configuration item by item, then quote against it.

Custom P/T Ports and OEM Gear Pump Builds for Distributors and Private Labels

Distributors covering several truck platforms and brand owners running a private-label line can have the pump built to their own specification.

Custom P/T port configurations

You can specify pressure and tank port position, thread type and size to suit the hose kits you already stock. Custom MOQ varies by product series and is confirmed together with the drawing.

Drafts and 3D renders before sampling

Design drafts and 3D renders are sent to you for approval before a sample is made. A change at this stage costs a revision, not a reworked batch.

Drawing-verified configuration

Port positions and mounting interfaces are checked against the drawing you approved. Quality checks also follow that drawing rather than a catalogue sheet. Any deviation is resolved before the batch ships.

Refundable tooling fee

If new tooling is needed, the fee is refunded in full once cumulative purchases of that model reach the agreed quantity. Quantities from separate orders count toward that total. The refund quantity is written into the quotation.

Stock Availability, MOQ and EXW Hebei Shipping Terms

MOQ, stocked models

1 piece

No minimum for stocked units

Lead time, stocked models

3–5 business days

Ships from stock

Custom / OEM MOQ and lead time

Per written quotation

Based on configuration and quantity; fixed before tooling

Incoterms

EXW Hebei, China

Handed over at the manufacturer's facility in Hebei

Payment

Per written quotation

Confirmed with the order

Quotation contents

Tiered unit pricing

Also covers tooling fee, refund quantity, warranty and EXW terms

Final Inspection Before Packing and One-Year Warranty Cover

  • 100% final inspection

    Every pump is inspected before packing. No unit is released on the strength of batch sampling alone.

  • Agreed checks and documents

    The quotation sets out the checks and paperwork. These cover dimensional checks, leak inspection, pressure and flow testing where applicable, and any documents you need for incoming inspection.

  • Where pumps are built

    Production takes place at a manufacturing partner in Ningjin, established in August 2010. The site is about 9 km from the Xinji sales office.

  • One-year warranty

    Olive Branch Hydraulics gives a one-year warranty, and the full terms are written into each quotation.

Get a Quote for N150-601100-000 Forklift Gear Pumps

Send the model or original part number, the quantity and your destination port. For replacement parts, also include the forklift model and equipment details. We reply within 24 hours with the confirmed match and pricing, or with the specific detail still needed to confirm it.

Request a Quote

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.