CBWL Compact Tandem Gear Pumps With Keyed And Four-Tooth Shafts

1 / 4

CBWL Tandem Gear Pump Parameters

Model pattern Front / rear displacement (mL/r) Catalogue L (mm) Weight (kg)
CBWL-E320/E320-**** 20/20 240 5.6
CBWL-E320/E316-**** 20/16 233 5.4
CBWL-E320/E310-**** 20/10 223 5.1
CBWL-E320/E308-**** 20/8 220.5 5.0
CBWL-E316/E316-**** 16/16 225 5.2
CBWL-E316/E310-**** 16/10 215 4.9
CBWL-E316/E308-**** 16/8 212.5 4.8
CBWL-E316/E306-**** 16/6 209 4.7
CBWL-E310/E310-**** 10/10 206 4.6
CBWL-E310/E308-**** 10/8 203.5 4.5
CBWL-E310/E306-**** 10/6 200 4.4

The 11 E-series catalogue combinations above specify 16 MPa rated and 20 MPa maximum pressure, optimum speed 1500–2500 rpm, speed range 800–3000 rpm and volumetric efficiency ≥92% under specified test conditions. Front and rear stage values must be confirmed for the selected configuration.

Separate photographed reference: CBWL-F314/F306-AFPL, nominal 14/6 mL/r by the observed model marking. Pressure rating, exact lengths and weight for this F-series reference are not verified by the E-series table and require its own approved specification.

Shaft And Mounting Drawing

P plain keyed shaft: nominal Ø16 mm, key width 5 mm, 40 mm overall projection and 20 mm keyed length dimension shown. H4 rectangular spline: 4 teeth, major Ø15 mm, minor Ø11.4 mm, 40 mm projection and 25 mm spline length dimension shown. The photographs show the keyed shaft version; the H4 option is documented in the original drawing.

The original drawing shows an oval flange with Ø80 mm pilot, 100 mm mounting-slot centres, 120 mm overall width and 11 mm slot width; it also shows a rectangular flange alternative with Ø38 mm pilot and 70 × 100 mm hole centres, four Ø9 mm holes. The catalogue overview reverses the pilot-to-flange descriptions, so use the selected original drawing and confirm dimensions before manufacture.

Connections: flange or screw configurations. E-series screw-port table lists M20×1.5 inlet and M18×1.5 outlet, each 16 mm deep. Do not transfer those thread sizes to the photographed flange-port configuration. Clockwise and counterclockwise versions are ordered separately.

Catalogue note: for rear displacement below 10 mL/r, selecting the single connecting plate can shorten overall length by 30 mm. Confirm whether each ordered assembly uses this configuration before applying the reduction to a reference length.

Product Information

CBWL Compact Dual Hydraulic Gear Pumps

Olive Branch Hydraulics manufactures hydraulic gear pumps and offers OEM/ODM production from approved samples and drawings. This listing groups the CBWL compact tandem pump style, documented displacement combinations and two shaft designs. The pictured assembly has two aluminium pumping sections, a central connecting section, an oval front flange, a plain keyed drive shaft and side flange-port faces.

Verified Models And Alternative Search Names

The catalogue lists CBWL-E320/E320, CBWL-E320/E316, CBWL-E320/E310, CBWL-E320/E308, CBWL-E316/E316, CBWL-E316/E310, CBWL-E316/E308, CBWL-E316/E306, CBWL-E310/E310, CBWL-E310/E308 and CBWL-E310/E306. All eleven combinations appear in the parameter table. Search descriptions include CBWL tandem gear pump, CBWL dual gear pump, CBWL double hydraulic pump, compact two-section pump, keyed shaft tandem pump and four-tooth rectangular spline tandem pump. These family names are grouped in one listing rather than published as duplicate products.

The photographed reference marking is CBWL-F314/F306-AFPL, corresponding to a nominal 14/6 mL/r combination. This observed F-series sample is identified separately from the E-series table. Similar external construction does not establish equal pressure grades, internal specifications or overall dimensions. No E-series pressure rating is assigned to the F314/F306 reference.

Shaft Options And Dimensional Confirmation

The reference installation drawing provides a plain keyed shaft and an H4 four-tooth rectangular spline. The photos illustrate the keyed option; the spline option is represented by its drawing, not by a separate sample photo. Confirm shaft diameter, key or spline dimensions, projection, mounting pilot and available installation space before production. No SAE involute spline option is claimed without a matching verified drawing.

The drawing shows oval and rectangular mounting alternatives. The photographed pump uses the oval style. Because the catalogue overview reverses the pilot descriptions relative to the dimension drawing, mounting selection must be based on the approved configuration drawing and checked dimensions. This listing does not treat the alternative pilot sizes as interchangeable.

Hydraulic Connections And Operating Limits

Flange-port and screw-port assemblies are listed as configuration options. The side flange-port faces visible in the photographs must be matched to the required fittings; the E-series screw thread values do not describe those photographed port faces. Verify both inlet and outlet positions, bore sizes, fastening threads and connecting pipework for each stage.

The E-series catalogue specifies 16 MPa rated pressure and 20 MPa maximum pressure, with an optimum speed of 1500–2500 rpm and a listed range of 800–3000 rpm. Operating conditions, fluid viscosity, temperature, inlet supply and duty cycle affect actual performance. Maximum pressure and speed are not a guarantee of continuous simultaneous operation at both limits. Rotation must match the drive direction as viewed from the shaft end; clockwise and counterclockwise configurations require confirmation when ordering.

Application, Part Numbers And OEM/ODM Enquiries

The catalogue describes agricultural machinery and other mobile hydraulic uses. Specific tractor, harvester or construction-machine models have not been independently verified for this assembly. No machine OEM material number is assigned. CBWL codes are pump model references; exact installation compatibility requires the original pump identification, dimensions and hydraulic requirements.

For a manufacturing quotation, provide clear photographs of the complete assembly, its original marking, the drive shaft, mounting face and both sides of the oil ports. Include front and rear displacement, rotation, pressure, speed, mounting dimensions and required quantity. Olive Branch Hydraulics can assess sample-based manufacture, drawing-based production, tooling and custom configurations after technical review. Final dimensions, materials, inspection requirements and marking are confirmed before manufacture. The installation drawing is supplied as an original dimensional reference; production follows an approved specification.

International Search Terms

The following are multilingual product descriptions for customer search. They do not indicate measured search volume or confirmed equipment fitment.

Market / language Product search phrases
English — international buyers CBWL tandem hydraulic gear pump; CBWL double gear pump; CBWL keyed shaft pump; CBWL 14/6 cc pump; CBWL 20/20 cc tandem pump
Russia / Kazakhstan — Russian CBWL сдвоенный шестеренный насос; CBWL двухсекционный гидравлический насос; насос CBWL со шпоночным валом
Mexico / Nicaragua / Latin America — Spanish bomba hidráulica doble de engranajes CBWL; bomba tándem CBWL; bomba CBWL con eje chaveteado
Egypt / Iraq / Arabic-speaking markets مضخة تروس هيدروليكية مزدوجة CBWL؛ مضخة هيدروليك ترادفية CBWL؛ مضخة CBWL بعمود ذي مفتاح
Türkiye — Turkish CBWL tandem hidrolik dişli pompa; CBWL çift dişli pompa; CBWL kamalı mil pompa
Brazil — Portuguese bomba hidráulica dupla de engrenagens CBWL; bomba tandem CBWL; bomba CBWL com eixo chavetado
Vietnam — Vietnamese bơm bánh răng thủy lực đôi CBWL; bơm thủy lực tandem CBWL; bơm CBWL trục then
Indonesia — Indonesian pompa roda gigi hidrolik tandem CBWL; pompa hidrolik ganda CBWL; pompa CBWL poros pasak
French-speaking markets pompe hydraulique double à engrenages CBWL; pompe tandem CBWL; pompe CBWL à arbre claveté

Model References, Nameplate And OEM Material Numbers

Family reference: CBWL. Complete observed sample marking: CBWL-F314/F306-AFPL. E-series model patterns and their displacement combinations are listed in the technical table above. These identifiers are pump model references, not independently verified machine OEM material numbers. A separate equipment OEM part number, manufacturer material number or confirmed cross-reference has not been established for this photographed assembly. Please supply the original equipment parts list or nameplate for verification.

Other CBWL-prefixed products from different manufacturers can use different mountings, displacement combinations and suffix systems. A shared family prefix alone does not establish interchangeability; unrelated references are not added as aliases for this assembly.

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.