6C040-37303 6C040-36300 Hydraulic Gear Pump For Kubota B And BX Tractors

1 / 6
Item Catalogue and fitment information
Current assembly number 6C040-37303 / 6C04037303
Earlier assembly references 6C040-37300 / 6C04037300, 6C040-36300 / 6C04036300, 6C040-36306 / 6C04036306, 6C040-36308 / 6C04036308
Equipment examples Selected Kubota B1700D, B2100D, B2400E, BX1800D, BX2200D, BX22D and BX23D tractors. Confirm model suffix and serial number.
Shaft and flange Compare drive profile, engagement length, locating pilot and bolt-hole centres with the original pump.
Port and rotation Confirm both port dimensions and orientation, and rotation viewed from the drive end.
Displacement, pressure and speed Confirm from the original pump specification and approved drawing.
Product Information

6C040-37303 Hydraulic Gear Pump for Kubota B and BX Tractors: Part Number Cross-Reference and Drawing-Matched Supply

Gear Pump Assembly

The 6C040-37303 hydraulic gear pump is the current assembly number for this position. It sits behind four earlier catalogue references on selected Kubota B and BX tractors, and we build it against confirmed drawings.

Five part numbers, one pump position. 6C040-37303 is the current assembly, and 6C040-37300, 6C040-36300, 6C040-36306 and 6C040-36308 are the earlier references you will find on older parts lists and pump nameplates. A matching number is where the check starts, not where it ends. The tractor model and serial range decide which configuration was actually fitted.

We produce this gear pump in Hebei, China, from a drawing or a physical sample that you confirm before production. Each unit is checked against that confirmed drawing for shaft end, flange, bolt pattern, pilot, ports and rotation. Stock may be listed under any of the five numbers, so the cross-reference below gives each one in hyphenated and unhyphenated form.

6C040-37303 Hydraulic Gear Pump for Kubota B and BX Compact Tractors

This is a manufacturer-built external gear pump, produced to a confirmed drawing for the 6C040-37303 assembly position. It applies to selected Kubota B and BX tractors only. Confirm the exact model and serial number before ordering, because pump configuration on compact tractors can change within a model's production run.

Kubota names and part numbers on this page are used for identification only. They do not indicate any affiliation with or approval by the original equipment brand. Displacement, pressure and dimensional data come from the drawing confirmed for your order, not from catalogue assumptions.

6C040-37303, 6C040-37300, 6C040-36300, 6C040-36306, 6C040-36308 Part Number Cross-Reference

Search and stock records may use either the hyphenated or the unhyphenated form of each number.

Common search terms for the same pump: Spanish and Portuguese bomba hidráulica Kubota; French pompe hydraulique Kubota; Russian гидронасос Кубота; Arabic مضخة هيدروليكية كوبوتا; Turkish Kubota hidrolik pompa; Chinese 久保田齿轮泵.

Reference Hyphenated Unhyphenated
Current assembly 6C040-37303 6C04037303
Earlier catalogue reference 6C040-37300 6C04037300
Earlier catalogue reference 6C040-36300 6C04036300
Earlier catalogue reference 6C040-36306 6C04036306
Earlier catalogue reference 6C040-36308 6C04036308

Interface Check

Shaft End, Flange, Bolt Pattern, Pilot, Ports and Rotation: What to Confirm Before Ordering

Mounting interface

A gear pump either fits the drive or it does not. The mounting interface decides that before any performance figure matters. The shaft end, whether splined, keyed or tapered, must match the drive coupling in form and engagement length, or the pump will not seat. The pilot is the spigot that centres the pump on its mount, and a pilot mismatch causes misalignment that typically shows up as shaft seal leakage and bearing wear. The flange profile and bolt pattern have to line up hole for hole with the mounting face.

Ports and rotation

Inlet and outlet ports must match the existing hoses in thread type, size and orientation. On gear pumps the inlet is usually the larger port. Rotation is normally stated as viewed from the shaft end. A pump turned against its specified rotation will not build flow and can be damaged within minutes.

Engineers should compare each item against the original pump or the drawing one by one. Purchasing can then use the photo checklist in the selection section to send the same information without disassembly. Use the confirmed drawing to verify numerical specifications.

Matching part numbers is the first step. Matching the interface is what confirms fit.

Kubota B1700D, B2100D, B2400E, BX1800D, BX2200D, BX22D and BX23D Tractor Applications

Typical duty on these models covers loader, three-point hitch and implement hydraulics.

Kubota B1700D

Small farm and property work. Confirm the serial number, as configuration can vary.

Kubota B2100D

Loader and mowing duties. Configuration may differ by serial range.

Kubota B2400E

Landscaping and light earthmoving. Check model and serial before ordering.

Kubota BX1800D

Grounds care and garden work. Serial number confirmation is required.

Kubota BX2200D and BX22D

Front loader and backhoe tasks. Configuration differs between serial ranges.

Kubota BX23D

Light trenching and digging. Confirm the exact model and serial.

Fitting the Gear Pump on a Kubota B or BX Tractor: Installation Checks

These are general checks. The tractor's service manual governs torque values and fluid specification.

Record before removal

Note the part number on the nameplate, the rotation direction and the port orientation of the installed pump.

Compare interfaces

Check the shaft end, flange and pilot of the new pump against the removed unit before mounting.

Clean mating surfaces

Clean the mounting face, the coupling and the hose ends so that no debris enters the suction line.

Tighten and refill

Torque the fasteners and refill the hydraulic fluid according to the tractor service manual.

First start-up

Bleed air from the system, then run at low idle and check for leaks and abnormal pump noise.

How Distributors and Engineers Choose the Right Kubota BX Hydraulic Pump

Start with the cross-reference

Use the table above to link the number on the old pump or parts list to the current assembly 6C040-37303. Treat an earlier number as a lead to verify, not as proof of interchange.

Provide model and serial

The tractor model and serial number identify which configuration was originally fitted. Without the serial number, we can only confirm the interface against photos or a drawing.

Send five reference photos

Photograph the nameplate, shaft end, flange face, ports and the overall pump. These five views let us check most interface features before any sample is made.

Distributor and engineer focus

Distributors can consolidate demand across several part numbers into one stocking list, quoted against confirmed configurations. Engineers should focus on rotation and port interfaces, where most fitting errors occur. Availability is confirmed per enquiry.

OEM, White-Label Packaging and Sample Matching for Gear Pump Programmes

We manufacture to your drawing or to a physical sample, and production starts only after you approve the configuration drawing. Quality control is tied to that approved document. Shaft end, flange, pilot, ports and rotation are checked against the drawing, and finished pumps are inspected before shipment.

White-label and custom packaging is available, including neutral or branded labels, colour boxes and carton shipping marks to your specification. MOQ, sample arrangements and lead time depend on the configuration and the packaging you choose. They are confirmed in writing in each project quotation.

6C040-37303 Gear Pump FAQ for Wholesale and OEM Buyers

Is 6C040-36300 interchangeable with 6C040-37303?
Not automatically. Earlier references such as 6C040-36300 lead to the current assembly, but interchange depends on the tractor serial range and on matching the shaft, flange, pilot, ports and rotation.
Can I search using the unhyphenated part number?
Yes. 6C04037303, 6C04036300 and the other unhyphenated forms refer to the same references as the hyphenated numbers.
How do I confirm rotation and port orientation?
Check the arrow or marking on the existing pump body, viewed from the shaft end, and photograph the ports from the same angle. If no marking is visible, a drawing or physical sample settles it.
Do you offer white-label packaging and sample matching?
Yes. We match configuration to your drawing or sample and supply labels, colour boxes and shipping marks to your specification.
How are MOQ and lead time set?
Both are confirmed per project in the quotation. They depend on the configuration, the packaging and your first-order quantity or annual volume.

Send Your Drawing, Sample Photos or Serial Number for a Gear Pump Quotation

Send the four items below. We confirm the configuration against your drawing or sample, then quote EXW Hebei, China.

Step 1

Part number

Send 6C040-37303 or any earlier reference, in hyphenated or unhyphenated form.

Step 2

Tractor and quantity

Give the tractor model and serial number, plus your first-order quantity or estimated annual volume.

Step 3

Drawing or photos

Attach a drawing or the five reference photos: nameplate, shaft end, flange face, ports and overall view.

Step 4

Packaging

State your requirements for neutral or branded labels, colour boxes and shipping marks. Your quotation then follows the confirmed configuration.

Catalogue drawing and search references

See the BX2200D hydraulic pump component diagram (J12500) for assembly identification. Confirm the tractor serial number and pump configuration when ordering.

Regional search terms: bomba hidráulica de engranajes Kubota 6C040-37303 (ES), pompe hydraulique à engrenages Kubota 6C040-37303 (FR), шестерённый гидронасос Kubota 6C040-37303 (RU), مضخة تروس هيدروليكية كوبوتا 6C040-37303 (AR), bomba hidráulica de engrenagens Kubota 6C040-37303 (PT), Kubota 6C040-37303 hidrolik dişli pompa (TR).

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.