35430-82200 35430-82202 Tandem Hydraulic Gear Pump For Kubota Tractors

Item Technical reference
Parts catalogue numbers 35430-82200, 35430-82202, 35430-82203
Search aliases 3543082200, 3543082202, 3543082203
Supplier cross-references 307016-0141 / 3070160141 and 2921. Confirm original label and configuration.
Pump type Tandem external hydraulic gear pump
Tractor references L3350DT, L3750/L3750DT, L4150/L4150DT/L4150DT-N, M4030SU/M4030SU-TF, M4050/M4050DT and listed M5030 variants. Match the tractor serial and hydraulic section.
Drive shaft Splined on the pictured reference. Confirm spline count, diameter and engagement length before order.
Fitment checks Mounting pilot, bolt pattern, port dimensions and orientation, rotation viewed from the drive end.
Displacement, pressure and speed Confirm against the pump nameplate and approved configuration.
Product Information

35430-82200, 35430-82202 and 35430-82203 Tandem Hydraulic Gear Pump for Kubota Tractors

35430-82200, 35430-82202 and 35430-82203 are three part numbers for the same Kubota tandem hydraulic gear pump position, but the shaft on the pump you remove decides which build is correct.

The Messicks Kubota parts catalogue lists 35430-82202 as the current reference for both 35430-82200 and 35430-82203. A matching part number does not settle the order on its own. WHD lists a splined reference configuration for the L3750 with manual shuttle, while other listings show a different shaft profile under the same number family.

We manufacture hydraulic gear pumps in China, and build each order against a drawing you have confirmed, or against your original pump. Before we quote, we compare the shaft, pilot, mounting holes, port orientation and rotation with your photos and tractor serial number. Trade terms are confirmed on the quotation.

Part numbers covered

35430-82200, 35430-82202 and 35430-82203, also written 3543082200, 3543082202 and 3543082203.

Configuration basis

Your confirmed drawing, or your original pump checked against photos and the tractor serial number.

Trade term

EXW China.

35430-82202 Tandem Hydraulic Gear Pump for Kubota L3750, L4150 and M4050 Tractors, Built to Your Confirmed Drawing

This tandem hydraulic gear pump is listed for the Kubota L3350DT, L3750/L3750DT, L4150/L4150DT, M4030SU and M4050/M4050DT, and for selected M5030 tractors. Buyers search for it under 35430-82200, 35430-82202 or 35430-82203, and under the hyphenless forms 3543082200, 3543082202 and 3543082203.

Each pump is configured against your confirmed drawing or your original pump. We do not build to the part number alone. The reference photo shows one supplied example. The shaft and port arrangement on your unit still has to match it before we quote.

35430-82200 vs 35430-82202 vs 35430-82203: Part Number Cross-Reference and Multilingual Search Terms

All three numbers lead to one current reference. The lower rows link the pump to the terms used in six other languages.

Reference Also written as Catalogue note
35430-82200 3543082200 Messicks lists 35430-82202 as the current reference
35430-82202 3543082202 Current reference in the Messicks Kubota catalogue
35430-82203 3543082203 Messicks lists 35430-82202 as the current reference
2921 2921 Independent supplier catalogue reference only
Spanish (ES) bomba hidráulica doble / bomba de engranajes tándem 35430-82200 / 82202 / 82203
French (FR) pompe hydraulique tandem / pompe à engrenages double 35430-82200 / 82202 / 82203
Russian (RU) шестеренный гидронасос тандем 35430-82200 / 82202 / 82203
Portuguese (PT) bomba hidráulica de engrenagens dupla 35430-82200 / 82202 / 82203
Arabic (AR) مضخة تروس هيدروليكية مزدوجة 35430-82200 / 82202 / 82203
German (DE) Tandem-Zahnradpumpe / Hydraulik-Doppelpumpe 35430-82200 / 82202 / 82203

Shaft Profile, Pilot, Mounting Holes, Port Orientation and Rotation: What Decides the Right Pump

These five points decide whether a 35430-82202 pump bolts on and runs. We check each one before we quote.

Shaft profile

WHD lists a splined shaft for the L3750 with manual shuttle, and other listings show a different profile. We compare a close-up of your shaft end with the drawing, including spline count or key form. A mismatch here rules the pump out.

Pilot

The pilot centres the pump on its mounting face. We check its diameter and depth against your photo, with a scale in the frame if possible, because a pilot that looks close can still prevent the pump from seating.

Mounting holes

We compare hole count, spacing and slot form on the flange. A pump with matching holes but a different pilot still needs to be flagged.

Port orientation

Inlet and outlet positions on both sections have to line up with the existing hoses and lines. Photos from above and from the side show this better than a written description.

Rotation

Rotation is usually stated as viewed from the shaft end. A pump turning the wrong way will not deliver flow, so we confirm it against the nameplate or the original port layout.

Kubota Tractor Models Listed for the 35430-82202 Tandem Pump

Catalogues list these models. Each one still has to be confirmed by serial number and hydraulic pump arrangement.

L3350DT

Listed. Check the serial number and the pump arrangement before ordering.

L3750 / L3750DT

Listed. A splined reference configuration is shown for manual shuttle units, so state the shuttle type.

L4150 / L4150DT

Listed. Compare the shaft and port photos with the serial range.

M4030SU

Listed. Confirm the pump arrangement against the original unit.

M4050 / M4050DT

Listed. Check the serial number and send nameplate photos.

Selected M5030

Applies to some units only. A serial number is required before we quote.

Fitting the Tandem Gear Pump on a Kubota Tractor: Pre-Installation Checks and Fitting Steps

Compare the old pump and the new pump side by side before fitting. Torque values and oil specifications come from the Kubota workshop manual for your tractor.

Compare both pumps

Place the old and new pumps together and check shaft profile, pilot, mounting holes and port orientation. If anything differs, stop before installing.

Confirm rotation

Check the rotation direction from the shaft end against the original unit or its nameplate.

Clean and reseal

Clean the mounting face, ports and lines, and replace all O-rings and seals at the joints.

Mount and torque

Fit the pump and tighten the fasteners to the values in the tractor manufacturer's manual.

Fill, bleed and test

Fill with the specified fluid and bleed air. Run at low speed, then check the ports and flange for leaks and unusual noise.

How Distributors and Workshops Avoid Mismatched Kubota Pump Orders

Why one part number can hide two shafts

Supersession settles which number to order, not which shaft is on the tractor. Messicks lists 35430-82202 as the current reference for both 35430-82200 and 35430-82203. WHD shows a splined configuration for the L3750 with manual shuttle, while other listings show a different shaft profile. A pump can be correct on paper and still not engage the drive on a given tractor, so we treat the part number as a starting point.

What we need before quoting

Send the tractor model, the serial number, a clear nameplate photo of the original pump, and close-ups of the shaft end and ports. Tell us the shuttle type, for example manual shuttle, because it is one of the factors that separates the listed shaft configurations. With this information we can match the order to a drawing, not to a guess, and the quotation covers the build that fits the tractor.

Grouping a mixed-model distributor order

For orders covering several models, group the lines by serial range and shaft profile, not by part number. We confirm each group against its own drawing or sample. Each line then ships with a confirmed configuration, and you do not end up holding one batch that fits only some of your workshop customers.

How each order is checked

Quality checks follow the confirmed drawing and the approved sample. For every configuration we check shaft profile, pilot, mounting holes, port orientation and rotation item by item before packing.

Order by serial number and shaft photo. The part number alone is not enough.

Private-Label Packaging, Sample Pumps and Drawing-Based OEM Configuration

OEM orders and private-label orders follow the same rule. We match the configuration first and agree the packaging second.

Drawing-based configuration — We build to your confirmed drawing, or we work from your original pump checked against photos and the serial number. If you have no drawing, the original unit is the reference.

White-label and custom packaging — Options include neutral packaging, your own labels, colour boxes and carton shipping marks. Artwork is confirmed before the batch is packed.

Sample before bulk — A sample pump can be requested for fitting on the tractor. Bulk production is scheduled after you approve the sample.

MOQ, lead time and price — These are quoted separately for each confirmed configuration and packaging specification.

Trade term — EXW China.

How a custom order runs

Requirement

Send the drawing or photos, the serial number, the quantity and your packaging details.

Sample

We configure a sample to the confirmed drawing.

Confirmation

You fit-test the sample and approve the configuration.

Production and delivery

The batch is built to the approved sample and delivered EXW China.

35430-82202 Tandem Pump Questions from Kubota Parts Buyers

How are 35430-82200, 35430-82202 and 35430-82203 related?
The Messicks Kubota parts catalogue lists 35430-82202 as the current reference for 35430-82200 and 35430-82203. The shaft profile still has to be confirmed for each tractor.
How do I confirm whether my pump has a splined shaft or another shaft type?
Send a straight-on photo of the shaft end, with a scale if possible, together with the tractor serial number. WHD lists a splined configuration for the L3750 with manual shuttle, and other listings show a different profile, so we check against your photo.
Can I order a sample before a bulk order?
Yes. You can request a sample pump to fit and test on the tractor. Sample cost and freight are quoted together with the configuration.
Do you supply neutral or private-label packaging?
Yes. Neutral packaging, white-label labels, colour boxes and custom shipping marks are available, and artwork is confirmed before packing.
What do you need from me for a quotation?
We need the tractor model, the serial number, the shuttle type, a nameplate photo, and close-ups of the shaft end, pilot, mounting holes and ports. Please also give the quantity and your packaging requirements.

Send Your Kubota Serial Number and Pump Photos for a 35430-82202 Quotation

Send photos and a serial number. We will confirm the configuration and quote EXW China, with a sample if you need one.

Send tractor details

Send the model, serial number and shuttle type.

Send pump photos

Send the nameplate, plus close-ups of the shaft end, pilot, mounting holes and ports.

State quantity and packaging

Tell us the order quantity and whether you need neutral, white-label or custom packaging.

Receive configuration check and quote

We match your details to a drawing, then quote EXW China and arrange a sample if you request one.

Additional part-number references

Some supplier listings use 307016-0141 or 3070160141 for this pump family. The 2921 designation is a separate supplier catalogue reference. Use the original pump label, tractor serial number and mounting dimensions to confirm either reference.

The product photograph shows a splined-shaft reference for the L3750 manual-shuttle application. For assembly identification, see the Kubota L3750DT manual-shuttle hydraulic pump exploded view (T08000). Confirm shaft, ports and mounting dimensions against your own pump.

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.