Tractor power steering
3539859M91 / 1824474M92 Hydraulic Steering Gear Pump for Massey Ferguson and Landini Tractors
This hydraulic steering gear pump is built to the 3539859M91 configuration, and we confirm the exact version against your sample or tractor serial before quoting.
Six part numbers are linked to this hydraulic steering gear pump, and they carry different weight. 3539859M91 is the primary reference. 1824474M92, 1824474M91 and 1823870M91 come from published cross-reference catalogues. SNP2/17S C001 and 20A17X506FALA are pump-supplier model references. A catalogue link between two numbers does not prove that every version is interchangeable. Shaft, flange, ports and rotation are checked against a physical sample before an order is confirmed.
The production pump has a single-section aluminium body with dark end covers, a square four-hole mounting flange, and a tapered-looking smooth drive shaft with a threaded tip and nut. Catalogues list it for Massey Ferguson 154 to 274C tractors and for Landini 5530 to 8530 F/L models and the C6830. Within each model, build year and serial number decide which version fits.
Primary reference — 3539859M91. Cross-references are listed separately and checked before quotation.
Not covered — 3539858M91 and 1824475M91 are separate parts and are not treated as this pump.
Origin and terms — Manufactured in Hebei, China. Prices are quoted EXW, and other Incoterms can be quoted on request.
Send sample photos for matching
Hydraulic Steering Gear Pump Overview: What 3539859M91 Covers
This pump supplies oil to the hydrostatic or power-assisted steering circuit on the Massey Ferguson and Landini tractor ranges listed below. We manufacture the gear pump to match the confirmed 3539859M91 configuration. Massey Ferguson and Landini names and numbers are used for identification only. The pump is not presented as a genuine Massey Ferguson part.
For distributors, the commercial value is a single pump with clearly documented cross-references. For OEM and private-label customers, the value is a sample-matched build. Shaft variants are approved separately, and packaging can carry your brand. Every quotation names the reference codes it covers, so a stock decision never depends on a catalogue line alone.
Key Features of the 3539859M91 Steering Pump
Physical identifiers taken from production photos. Exact drive dimensions are confirmed against your sample.
Single-section aluminium body
The pump has one gear section in an aluminium housing with dark end covers. That gives one pressure outlet feeding the steering circuit. Multi-section pumps listed under neighbouring MF numbers are not covered by this part.
Square four-hole mounting flange
The pump bolts to the engine or timing cover through a square flange with four holes. Bolt pitch and pilot diameter differ between pump families that look alike, so we check both against your sample before production.
Tapered-looking shaft with threaded tip and nut
The drive shaft is smooth, has a tapered profile and ends in a threaded tip with a retaining nut. Taper angle, length and key or seating detail have to match your drive gear. A shaft that is close but not exact will not seat correctly.
Port position and thread
The inlet and outlet positions, thread type and size are matched to the sample. Ports that end up on the wrong side or carry a different thread form are a common cause of returns on look-alike pumps.
3539859M91 Cross-Reference Table
How each code relates to this pump, and where the limits are.
Published catalogues list a nominal displacement of 17 cm³/rev for this reference family. Sonic lists its MF-M-3539859-PM version as counter-clockwise, while Haoan lists right-hand rotation under the same reference numbers. Confirm the direction and viewing convention from the original pump before ordering. Rated pressure and speed must be confirmed for the supplied configuration.
| Reference code |
Source |
How we treat it |
| 3539859M91 |
Massey Ferguson reference |
Primary reference for this pump |
| 1824474M92 |
Chinese Sanye and Elephant catalogues |
Cross-reference, confirmed by sample |
| 1824474M91 |
HydroPack catalogue |
Cross-reference, confirmed by sample |
| 1823870M91 |
HydroPack catalogue |
Cross-reference, confirmed by sample |
| SNP2/17S C001 |
Pump supplier model reference |
Not our SKU; no interchangeability implied |
| 20A17X506FALA |
Pump supplier model reference |
Not our SKU; no interchangeability implied |
| 3539858M91, 1824475M91 |
Separate MF references |
Not covered; do not merge |
Material and Construction
The housing is aluminium, which keeps the pump light on a front-mounted engine drive. External gear pumps of this type typically run a pair of hardened steel gears inside the housing, supported by bushings or bearing blocks, with a shaft seal at the drive end. Internal tolerances between the gear tips and the housing bore control volumetric efficiency, so these surfaces are machined rather than left as cast.
The smooth tapered shaft and threaded nut transfer drive torque through the taper fit, so the shaft surface finish matters. Material grades and internal dimensions are not listed for this part. They are agreed against your sample or drawing during sample approval.
How a Tractor Steering Gear Pump Works
The engine drives the shaft and turns two meshing gears. Oil fills the spaces between the gear teeth and the housing on the inlet side. The gears carry it around the outside to the outlet, and where the teeth mesh again the oil is forced out. Output flow follows shaft speed and displacement, so it rises with engine rpm.
The pump itself does not set system pressure. The steering valve and its relief protection limit pressure, while the pump delivers flow against the resistance the circuit creates. This configuration must use the specified direction of rotation. Running it the wrong way leads to loss of prime and seal damage, which is why rotation is checked before every order.
Quality Control Process
Inspection is run against your approved sample, not a generic catalogue profile.
Reference sample approval
The approved sample or drawing becomes the master for shaft, flange, ports and rotation. Each change to it is recorded and confirmed in writing.
Incoming parts check
Housings, gears, shafts and seals are checked against the agreed dimensions before assembly. Parts that are out of tolerance are held back.
Machining and assembly checks
Gear bores, flange faces and shaft tapers are measured during production. Assembly is checked for free rotation and correct seal fitting.
Pre-shipment inspection
Before packing, each batch is checked for identifiers: flange pattern, shaft profile, port positions, rotation marking and labelling. The inspection scope for your order is stated in the quotation.
Which Tractors Use the 3539859M91 Steering Pump?
These are catalogue-listed reference applications. Confirm the serial number for each machine.
Massey Ferguson wheeled tractors
MF 154F, 154S, 164 TS, 174F, 174S, 184F, 184S, 194F, 194S. These are narrow and specialist tractors where the steering pump is driven from the engine.
Massey Ferguson crawler
MF 274C is listed. Check the serial number, because crawler builds can differ in drive arrangement.
Landini F and L ranges
5530F, 5530L, 6030F, 6030L, 6530F, 6530L, 7530F, 7530L, 8530F, 8530L, as listed in the HydroPack catalogue.
Landini crawler
C6830 is listed in the HydroPack catalogue. Confirm the serial before ordering.
Parts distribution and workshops
Distributors stocking for these fleets usually hold the primary number and sell against the cross-reference table above.
Installation Guide
Compare before removal
Lay the new pump next to the old one and compare the flange, shaft taper, nut thread, port positions and rotation arrow before you strip anything.
Clean the mounting face
Remove the old gasket or O-ring residue and any debris from the drive area. Fit a new seal of the correct type.
Seat the shaft and tighten
Engage the drive gear on the taper, then tighten the shaft nut and the four flange bolts evenly to the tractor manufacturer's torque values.
Connect and prime
Fit the suction and pressure lines without crossing them. Fill the pump inlet with clean oil and check the oil level.
Start and check
Run the engine at idle and turn the steering from lock to lock. Check for noise, leaks and steering response before working the tractor under load.
Maintenance and Service Life
Oil cleanliness
Change oil and filters at the tractor manufacturer's intervals. Contaminated oil wears the gear and bushing surfaces first.
Suction side
A blocked strainer or a leaking suction hose can cause aeration and noise and shortens pump life.
Shaft nut and seal
Check the drive end for seepage at each service. A loose taper nut damages the shaft seat.
Service life
Service life depends mainly on oil condition, operating temperature and drive alignment rather than running hours alone.
How to Choose the Right Steering Gear Pump Version
Six checks that separate a correct match from a look-alike.
Tractor model and serial
Send the full model designation and chassis serial. Version changes within a model usually follow serial ranges.
Part number on the old pump
Read every code on the label or casting. Any supplier code such as SNP2/17S C001 or 20A17X506FALA helps us trace the pump.
Shaft
Photograph the taper, threaded tip and nut. If you can, measure the shaft diameter and length.
Flange
Measure the bolt-hole spacing and the pilot diameter across the square four-hole flange.
Ports
Note the inlet and outlet sides and the thread type and size.
Rotation
Viewed from the shaft end, state clockwise or anticlockwise, or send the old pump as a sample.
OEM and Private Label Steering Pumps
Custom work starts from your sample or drawing, and each variant is approved separately.
Sample matching
We match the pump to your physical sample for shaft, flange, ports and rotation before tooling.
Custom shaft variants
Alternative shaft profiles are developed and approved one variant at a time. Each variant is not assumed to fit other tractors.
Tooling development
Tooling is made where a dimension cannot be met with existing tooling. The cost and timing are stated in the quotation.
Private brand packaging
Your logo, labels and carton print can be applied, with the part number cross-references you specify.
How custom orders run
Requirement
You send the sample or drawing, the codes and the expected quantity.
Sample
A matched sample is built for checking on your tractor.
Confirmation
You approve the sample and the packaging artwork in writing.
Mass production and delivery
Production follows the approved sample, then the goods are packed and handed over EXW Hebei or on the agreed Incoterm.
Packaging and Shipping
Unit packing
Each pump is boxed individually with its ports plugged and the shaft protected.
Neutral or branded cartons
We supply plain cartons or your private-label print, with the codes printed on the label.
Carton data
Carton size, gross weight and quantity per carton are stated in the quotation for your order.
Incoterms
EXW Hebei, China, as standard. FOB or CIF can be quoted on request.
MOQ and Lead Time
Commercial terms are fixed in the written quotation for each part number and variant.
| MOQ |
Set per quotation · Separate figures for standard and private-label orders |
| Price tiers |
By order quantity · Tier breaks listed in the quotation for distributors |
| Lead time |
Confirmed in quotation · Standard build and custom variants are quoted separately |
| Samples |
Available for matching · Sample cost and timing stated in the quotation |
| Incoterms |
EXW Hebei, China · Other terms on request |
| Payment |
Confirmed in quotation · Agreed before the order is confirmed |
Warranty and After-sales Support
Warranty terms
The warranty period and its conditions are written into the quotation for the part number supplied.
Claim information
A claim needs photos, the label code, the tractor serial and installation details.
Configuration basis
Cover applies to the configuration confirmed against your sample or serial.
Technical follow-up
Fitting questions are answered by engineers working from your order's approved sample record.
Steering Gear Pump FAQ
- Is this a genuine Massey Ferguson part?
- No. We manufacture it to the 3539859M91 configuration, and the Massey Ferguson and Landini numbers are used only for identification.
- Are 3539858M91 and 1824475M91 the same pump?
- No. They are separate references and are not covered by this pump. Send those codes as a separate enquiry if you need them.
- Are SNP2/17S C001 and 20A17X506FALA your model numbers?
- No. They are pump-supplier model references that help with identification. They are not our SKUs and do not prove that every version is interchangeable.
- What do you need to confirm the fit?
- The tractor model and serial, every code on the old pump, and photos of the shaft, flange and ports. The fastest route is to send the old pump as a sample.
- Can I send an enquiry in my own language?
- Yes. Quote the part codes and they will identify the pump in any language. Common terms are bomba de dirección hidráulica (ES), bomba de direção hidráulica (PT), насос гидроусилителя руля (RU), مضخة توجيه هيدروليكية (AR), hidrolik direksiyon pompası (TR), pompe de direction hydraulique (FR), bơm trợ lực lái thủy lực (VI) and pompa power steering hidrolik (ID).
Request a Quote or Matching Sample for 3539859M91
Send the codes on your old pump, the tractor serial and your quantity. You will receive a quotation that states the codes covered, sample terms, MOQ tiers and EXW price.
Request quotationArrange a matching sample
Part codes from the label or casting, Tractor model and serial number, Photos of the shaft, flange and ports