1927P00101 Agricultural Tractor Hydraulic Steering Gear Pump

1 / 3
Parameter Specification
Reference code 1927P00101 (equipment / catalogue reference)
Pump type External gear pump, power steering
Pump body Aluminium
Flange and end cover Dark finish, two mounting holes
Shaft Threaded tip with retaining nut
Port protection Red protectors fitted
Fitment basis Sample plus tractor model and serial
Incoterm EXW Hebei, China
Product Information

1927P00101 Hydraulic Steering Gear Pump for Massey Ferguson Agricultural Tractors

The 1927P00101 hydraulic steering gear pump is an external gear pump for Massey Ferguson tractor power steering circuits. It is built in Hebei, China, and every configuration is matched to your sample before the quotation is fixed.

Start at the drive end. The shaft has a threaded tip and a retaining nut, and that detail decides whether the pump will seat on the tractor drive at all. The thread, the drive profile and the nut position must agree with the unit removed from the machine. Behind the shaft is a single aluminium pump body. A dark-finished mounting flange and end cover close the body, two mounting holes locate it, and the ports ship under red protectors.

1927P00101 is an equipment and catalogue reference used to identify the application. It is not our internal SKU, and the pump is not sold as a genuine Massey Ferguson part. The spaced form 1927 P00101 refers to the same code. For accurate configuration matching, Olive Branch Hydraulics confirms displacement, pressure, rotation and connection layout from your sample and tractor serial number, not from a list.

  • Reference — 1927P00101. The search form 1927 P00101 refers to the same code.
  • Matching basis — A physical sample, plus the tractor model and serial number.
  • Supply terms — EXW Hebei, China. All commercial terms are set in the quotation.

Request a fitment check

What Is the 1927P00101 Hydraulic Steering Gear Pump?

This pump supplies oil flow to the power steering circuit of Massey Ferguson agricultural tractors identified under reference 1927P00101. Its job is narrow and practical. It has to bolt on, connect, and deliver the flow the steering valve expects on the machine and serial range confirmed from your sample. Each unit is produced to that confirmed configuration rather than taken from a generic catalogue entry.

Model coverage is never attached to the code without evidence.

Fitment to a specific tractor is stated only after the sample, the serial number and the connection layout have been checked. This protects distributors from stocking a pump that matches the code but not the machine.

Key Features of the Steering Gear Pump

Each feature below can be seen on the physical pump and checked against your removed unit.

Aluminium pump body

The gear housing is a single aluminium body, which keeps weight down and conducts heat away from the gear set. Aluminium housings typically rely on closely machined gear bores, so bore dimensions are part of the check against your sample.

Threaded shaft tip with retaining nut

The drive shaft ends in a threaded tip secured by a retaining nut, which holds the drive member in axial position. Thread and drive geometry are taken from your sample, not assumed from the code.

Two-hole flange mounting

A dark-finished flange with two mounting holes locates the pump on the drive housing. Hole spacing and pilot dimensions are measured from the sample, because a small offset causes shaft misalignment and early seal wear.

Port protectors fitted

Red protectors cover the ports from assembly until hoses are connected, keeping debris out of the gear chamber. Remove them only when the fittings are ready.

1927P00101 Technical Specifications and Matching Points

Four items decide fitment: the shaft drive, the flange, the ports and the hydraulic rating. All four are checked against your sample.

Displacement, pressure and speed are confirmed against the sample and machine serial number before quotation.

Reference code 1927P00101 (equipment / catalogue reference)
Search spelling 1927 P00101 (same code, spaced)
Pump type External gear pump, power steering duty
Pump body Aluminium
Flange and end cover Dark finish, two mounting holes
Shaft Threaded tip with retaining nut; drive profile matched to sample
Port connections Thread confirmed from sample; red protectors fitted
Displacement / pressure / rotation Confirmed from sample and tractor serial
Application Massey Ferguson tractor power steering, serial confirmed

Material and Construction

Housing and covers

The housing is aluminium, and a dark-finished flange and end cover close the gear chamber at each end. In this pump layout, the end cover is typically sealed to the body with an O-ring or gasket and clamped by through-bolts. Cover flatness and bolt torque therefore govern internal leakage. Material grades for the gears and shaft are stated in the quotation once the configuration is matched.

Drive end

The shaft passes through the flange via a lip seal, which is typically the first point of external leakage on a worn gear pump. The threaded tip and retaining nut must reproduce the original drive arrangement so the shaft runs without side load.

How a Hydraulic Steering Gear Pump Works

How flow is generated

Two meshing gears turn inside the aluminium body. Oil fills the tooth spaces on the inlet side and is carried around the outside of each gear, against the housing wall. It is pushed out at the outlet side where the teeth come back into mesh. Output per revolution is fixed by gear width and tooth geometry, so flow rises in proportion to drive speed.

What sets pressure

The pump does not set pressure. The steering valve load and the circuit relief valve do. This is why rotation and displacement must match the original unit. A pump with the wrong rotation will not deliver oil to the outlet port. A mismatched displacement changes steering response and how much oil passes over the relief valve, which adds heat to the circuit.

Quality Control Process

The inspection scope is agreed for each order and written into the quotation.

  1. Agree the scope

    Before production, we list the dimensions to be checked, the functional checks to be run and the report format you will receive.

  2. Incoming parts

    Castings, gears and shafts are checked against measurements taken from your approved sample. The focus is on bores, the shaft drive and flange geometry.

  3. Assembly

    Gear fit, cover bolt torque and shaft seal seating are checked at assembly, to the agreed scope.

  4. Pre-shipment inspection

    Units are inspected against the agreed list before packing. Third-party inspection at the Hebei factory can be scheduled before EXW release.

Where the 1927P00101 Steering Pump Is Used

Massey Ferguson tractor power steering

The pump supplies the steering circuit on the model and serial range confirmed from your sample. Field duty includes cold starts and long idle periods, so oil condition matters as much as the pump.

Workshop overhaul of steering circuits

Workshops repairing in-service tractors order against the removed pump, which serves as the matching sample.

Distributor stock

Distributors serving regions with established Massey Ferguson fleets stock the pump in neutral or private-label packaging once fitment is confirmed.

Farm fleet operators

Operators running several tractors of one series can match a single sample and record the serial number of each machine at order.

Installation Guide

  1. Compare units

    Lay the new pump next to the removed one. The shaft tip and nut, flange holes, port positions and rotation marking should all agree.

  2. Clean the circuit

    Drain the oil and change the filters as set out in the tractor manual. Debris from a failed pump will damage new gears.

  3. Mount

    Fit the pump with a new flange seal and tighten the bolts evenly. Torque the retaining nut to the tractor manual figure.

  4. Connect and prime

    Remove the red protectors, connect the hoses, and fill the inlet with clean oil so the pump never runs dry.

  5. Start and bleed

    Start at idle and steer slowly from lock to lock to purge air. Then check for leaks, noise and steering effort.

Maintenance and Service Life

  • Oil

    Use the grade and change interval given in the tractor operator's manual.

  • Suction filter

    A blocked filter typically shows up as whine and slow steering caused by cavitation.

  • Shaft seal

    Oil at the flange is usually the first sign of seal wear, so check it at every service.

  • Aeration

    Foamy oil usually points to an air leak on the suction side rather than a pump fault.

  • Service life

    Life depends mainly on oil cleanliness, temperature and duty cycle, so no fixed hour figure is claimed.

How to Choose the Right Steering Gear Pump for Your Tractor

  1. Identify the machine

    Record the tractor model, the serial number and the code on the removed pump, whether it appears as 1927P00101 or 1927 P00101.

  2. Provide the sample

    A physical sample is preferred. If that is not possible, send photos and measurements of the shaft, flange and ports, with a note on rotation. Final matching uses the measured configuration.

  3. Confirm the match

    You receive a fitment confirmation covering the drive, flange, ports and hydraulic rating before volume pricing is quoted.

  4. Choose the supply route

    Distributors list their quantity breaks. Private-label buyers add packaging files. OEM buyers add any required changes.

  5. Approve a pre-production sample

    Fit the sample on a tractor of the confirmed serial range before releasing the batch order.

OEM, ODM and Private-Label Options

  • Private-label packaging

    Your logo, carton artwork, labels and barcodes can be applied. Brand files are used only for your orders.

  • Product marking

    The part reference and your own code are marked by a method agreed at sampling.

  • Tooling

    Where a feature of your sample differs from existing tooling, new tooling is quoted separately.

  • Confidentiality

    NDA terms can be agreed before you share samples or files.

How custom orders work

  1. Request

    Send the sample, serial number, quantities and packaging brief.

  2. Sampling

    A matched sample is built. Cost and timing are stated in the quotation.

  3. Approval

    You approve the sample and the packaging proof.

  4. Production and delivery

    The batch is built to the approved sample, inspected to the agreed scope and released EXW Hebei, China.

Packaging and Shipping

Port protection

Red protectors stay on the ports through shipment.

Unit packing

Each pump is packed individually in a neutral or private-label box.

Cartons

Units per carton, carton size and gross weight are confirmed in the quotation once the box format is fixed.

Incoterm

EXW Hebei, China, with your forwarder collecting. State in your RFQ if you need a different Incoterm.

MOQ and Lead Time

All figures are fixed in a written quotation after fitment is confirmed.

MOQ

Set in quotation

Depends on packaging format and tooling needs

Quantity breaks

Quoted at the volumes you list

Lets distributors plan resale margin

Sample

Built to your sample

Cost and timing stated in quotation

Production lead time

Confirmed at order

Starts after sample and packaging approval

Payment

Agreed in quotation

Stated per order

Incoterm

EXW

Hebei, China

Warranty and After-Sales Support

Warranty terms

Coverage and period are stated in the quotation for each order.

Claim details

Include the part code, tractor serial, hours on the pump, photos and oil condition.

Root-cause review

Returned units are checked against the approved sample and the inspection record.

Repeat batches

Repeat orders are built to the same approved sample.

1927P00101 Steering Pump FAQ

Is 1927P00101 your internal part number?
No. It is an equipment and catalogue reference, and 1927 P00101 is the same code with a space. The form 1927OP00101 that appears in some listings is a typo, not another code. The pump is not sold as a genuine Massey Ferguson part.
Which Massey Ferguson models does it fit?
Only the models and serial ranges confirmed from your sample. Model coverage is confirmed against the sample and machine serial number.
Can you quote displacement and pressure before matching?
No. These values are confirmed from your sample and serial number and then written into the quotation.
Are regional distribution terms available?
They are discussed on request. Send your territory, your current sales channel and your expected annual quantity, and the agreed terms are set out in writing.
What search terms can my team use in other languages?
Use the code with the local term. EN: 1927P00101 hydraulic steering gear pump; ES: bomba de engranajes de dirección hidráulica 1927P00101; PT: bomba de engrenagens da direção hidráulica 1927P00101; RU: шестерённый насос гидроусилителя руля 1927P00101; AR: مضخة تروس التوجيه الهيدروليكي 1927P00101; TR: hidrolik direksiyon dişli pompası 1927P00101; FR: pompe à engrenages de direction hydraulique 1927P00101; VI: bơm bánh răng trợ lực lái thủy lực 1927P00101; ID: pompa roda gigi power steering hidrolik 1927P00101.

Request a Fitment Check and Quotation for 1927P00101

Send the tractor model and serial number, photos or a sample of the removed pump, your quantity breaks, and your destination market with any certification or document requirements. You receive a fitment confirmation, an EXW Hebei quotation with sample terms, and a list of the documents that can be supplied for that market.

Request a fitment check

Photos are enough to start the review, Quantity breaks are priced as listed, Packaging options are confirmed at quotation

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.