How To Add A Hydraulic Pump To A Tractor
Learn how to add an auxiliary hydraulic pump to your tractor. Covers pump selection, installation steps, and t…
| Item | Catalogue and selection information |
|---|---|
| Current assembly reference | TC050-36440 / TC05036440 |
| Earlier catalogue references | TC050-36400 / TC05036400, TC050-36403 / TC05036403, TC050-36407 / TC05036407, TC050-36409 / TC05036409 |
| Supplier cross-reference | 1901-1005 (Atlantic Quality Parts) |
| Equipment examples | Kubota L3940, L4240, L5240, L5740 and MX5000 configurations listed in equipment and supplier catalogues. Confirm model suffix and serial. |
| Shaft and mounting | External spline in reference photos. Confirm tooth count, diameter, engagement length, mounting pilot and bolt pattern. |
| Ports and rotation | Confirm connection dimensions and orientation, and rotation viewed from the input shaft. |
| Displacement, pressure and speed | Confirm using the original pump identification and approved drawing. |
The TC050-36440 hydraulic gear pump is matched by its splined input shaft and two oil-port bosses, then built to the drawing or sample you confirm.
Check the input shaft first. The reference unit for TC050-36440 shows a splined input and two raised oil-port bosses. Those features, together with the mounting face, decide whether a pump seats and seals on a given Kubota tractor. The same pump family is catalogued under TC050-36400, TC050-36403, TC050-36407 and TC050-36409, and TC050-36440 is the current reference.
We manufacture hydraulic gear pumps and tractor pumps in Hebei, China. Each order is configured against the drawing or original pump you send, not against a catalogue number alone, because fitment changes with the tractor serial number. Quotations are EXW Hebei.
Current reference — TC050-36440 supersedes the earlier TC050-364xx numbers listed further down.
Matching basis — Spline, ports, mounting face and rotation are confirmed from your drawing or sample before production.
This hydraulic gear pump is listed for Kubota L4240, L5240 and MX5000 series tractors under the current catalogue number TC050-36440. We produce it as a manufacturer, and the configuration is fixed against the drawing or sample you approve. A part number match alone does not confirm fitment. The tractor serial number and the markings on the original pump do.
Kubota model names and part numbers appear here for identification only and imply no affiliation with Kubota. Supply terms are EXW Hebei, China, with packaging agreed per order.
The reference photo shows a splined input and two oil-port bosses. Every other dimension comes from your drawing or sample.
Send the original shaft or a drawing that shows the spline. We do not assume tooth count or pitch from photos, so the shaft is cut only to a confirmed profile.
Port size, thread type and boss position are taken from your sample or drawing. A photo showing both ports from above lets us cross-check orientation before quoting.
Flange pattern, pilot diameter and bolt spacing are measured on the original unit or read from your drawing. If neither is available, we do not quote a fitment.
Rotation direction, displacement, pressure, speed and circuit are not inferred. They are set to your documentation, because the TC050 numbers can differ on these points by serial range.
Five catalogue references point to this pump family, and TC050-36440 is the current one.
Search terms in other languages: bomba hidráulica Kubota (ES), pompe hydraulique Kubota (FR), гидронасос Кубота (RU), مضخة هيدروليكية كوبوتا (AR), bomba hidráulica trator Kubota (PT), Kubota hidrolik pompası (TR).
| Catalogue number | No-hyphen spelling | Status |
|---|---|---|
| TC050-36440 | TC05036440 | Current reference |
| TC050-36400 | TC05036400 | Earlier reference |
| TC050-36403 | TC05036403 | Earlier reference |
| TC050-36407 | TC05036407 | Earlier reference |
| TC050-36409 | TC05036409 | Earlier reference |
| Atlantic Quality Parts 1901-1005 | 19011005 | Third-party search reference only |
These are the listed models. In each case, the serial number decides fitment.
Confirm the serial number and the original pump nameplate before ordering.
Fitment depends on serial range, so check the original pump marking.
Verify the serial number and pump identification on the installed unit.
Match the serial number and nameplate before confirming the TC050 number.
Fitment is serial-dependent, so confirm the original pump marking.
Only some L3940 builds apply, so the serial number and pump label are mandatory.
Follow the tractor's service manual for torque values and bleeding procedure. The sequence below covers the checks that prevent most fitting faults.
Compare the tractor serial number and the original pump marking with the TC050 number on the supplied unit before you remove anything.
Hold the new pump beside the old one. Check the spline, both oil-port bosses and the flange pattern side by side.
Remove old gasket material and debris from the housing face. Inspect the area for burrs that could tilt the pump.
Slide the shaft into the drive coupling without forcing it. The pump should seat flush before any bolt is tightened.
Fit new seals or O-rings at both port bosses. Tighten fittings to the values in the model service manual.
Bleed air from the circuit before the first start. Run the engine at idle and check both ports and the flange for leaks.
Five catalogue numbers for one pump family mean a counter sale can go wrong on shaft, port or rotation even when the model name matches. Distributors who record stock by TC050 number and the serial range it serves see fewer returns than those who stock by tractor model alone. Asking customers for a nameplate photo and the tractor serial at the point of order costs a few minutes. It also removes most mismatch disputes.
Each production batch is built to the approved drawing for that reference and is checked at final inspection for spline, port position and mounting face against that drawing. When your customers return to you for repeat orders, they get the same configuration. Tiered pricing is quoted by quantity per TC050 reference. Send your expected volumes per number and we will return price breaks for each. Regional distribution arrangements are discussed case by case, based on the volumes and markets you put forward.
Private label and OEM programmes start from your drawing or physical sample.
Spline, ports, mounting face and rotation are built to your approved drawing. Any change to the drawing triggers a new sample approval.
Plain boxes, your logo cartons or custom labels are available. Artwork and carton marking are confirmed together with the sample.
Customer drawings and samples are handled as confidential and are used only for your order. An NDA can be signed before you send files.
Send a drawing, 3D file or original pump.
We confirm the configuration and the points that remain open.
You approve a pre-production sample before batch work starts.
The batch is built to the approved sample. MOQ and lead time are confirmed for each project.
Send the items below to get an EXW Hebei quotation and a configuration check against your tractor.
Model and full serial number.
Original part number or a clear nameplate photo.
Photos or a drawing of the spline and both oil-port bosses.
Quantity per reference, packaging requirements, and whether you need a sample first.
TC050-36440 (TC05036440) is the current catalogue reference for TC050-36400 (TC05036400), TC050-36403 (TC05036403), TC050-36407 (TC05036407) and TC050-36409 (TC05036409). Atlantic Quality Parts lists 1901-1005 as a supplier search reference.
The L4240HSTC-3 hydraulic pump exploded view (H12500) lists the complete assembly at item 010. Use the drawing for component identification and confirm actual mounting dimensions separately.
Search terms: bomba hidráulica de engranajes Kubota TC050-36440 (ES), pompe hydraulique à engrenages Kubota TC050-36440 (FR), шестерённый гидронасос Kubota TC050-36440 (RU), مضخة تروس هيدروليكية كوبوتا TC050-36440 (AR), bomba hidráulica de engrenagens Kubota TC050-36440 (PT), Kubota TC050-36440 hidrolik dişli pompa (TR), 久保田 TC050-36440 拖拉机液压齿轮泵 (ZH).
Learn how to add an auxiliary hydraulic pump to your tractor. Covers pump selection, installation steps, and t…
Skip priming and your gear pump dies in seconds. Learn the 5-minute procedure that prevents scoring, cavitatio…
Discover how hydraulic gear pumps work, why they still dominate industry, and key components to watch when spe…
Compare the most trusted hydraulic gear pump brands with a data-driven ranking built for procurement teams who…
Contact us now for a professional solution and fast quote.
Fill in your info to start a conversation.