CBGJ3115/3100L Tandem Hydraulic Gear Pump 9G667-56B010000A0

1 / 2
Model CBGJ3115/3100L
Part number 9G667-56B010000A0
Type Tandem hydraulic gear pump
Equipment Foton Lovol wheel loaders, subject to serial number confirmation
Product Information

CBGJ3115/3100L Tandem Hydraulic Gear Pump 9G667-56B010000A0 for Foton Lovol Wheel Loaders

CBGJ3115/3100L tandem hydraulic gear pump 9G667-56B010000A0

The CBGJ3115/3100L tandem hydraulic gear pump, part number 9G667-56B010000A0, is supplied for Foton Lovol wheel loader hydraulic systems and built to a configuration confirmed against your drawing or original pump data.

A loader working an aggregate stockpile starts lifting slowly under a full bucket, and the steering feels heavy at idle. The workshop pulls the tandem gear pump and finds a worn nameplate, two sections and four ports. The same pump model can be built in different configurations, so the next order has to match the unit that came off the machine, section by section.

We manufacture tandem hydraulic gear pumps in Ningjin, Hebei, China, and match each order to a drawing confirmed by the customer before production. Shaft, rotation, port layout and section data are checked against that drawing. Units ship EXW Hebei, with white-label or custom packaging available for distributors and brand owners.

  • Exact identification — Model CBGJ3115/3100L and part number 9G667-56B010000A0 are quoted exactly as marked, without substitute codes.
  • Drawing-based build — Production starts only after the configuration has been confirmed against your drawing, nameplate and photos.
  • Pre-shipment inspection — Each order is checked against the confirmed drawing before it leaves the factory.

CBGJ3115/3100L Tandem Hydraulic Gear Pump 9G667-56B010000A0 for Foton Lovol Wheel Loaders

CBGJ3115/3100L is a two-section tandem hydraulic gear pump. It is supplied for Foton Lovol wheel loaders under part number 9G667-56B010000A0. We do not use the model code to infer displacement, pressure, shaft or rotation. Every unit is configured against a drawing you confirm, and all critical interfaces are checked before production. Manufacturing takes place at our Hebei facility, and goods are sold EXW. The pump is offered as a compatible part. It is not presented as a product made by or for the original machine brand.

Key Parameters to Confirm Before Ordering a CBGJ3115/3100L Tandem Gear Pump

Four data points decide whether a tandem gear pump will work on the machine, and none of them can be read reliably from the model code.

Section displacement and working pressure

Displacement and working pressure must be confirmed separately for each section. In a tandem pump, the two sections usually feed different circuits, and their flow is often different. Typical loader layouts split work hydraulics from steering or pilot supply. The figures should come from the original nameplate, the part number record or your drawing. They should not come from the digits in CBGJ3115/3100L, because similar codes can cover different builds.

Shaft, rotation and port arrangement

The drive shaft and the mounting flange must match the gearbox or power take-off. That means checking the spline or keyed form, the tooth count and the pilot diameter. Rotation is defined looking at the shaft end, and must match the original pump configuration. Port type, thread standard and position must also match the existing hoses. Otherwise the installer has to adapt fittings on site.

Part number 9G667-56B010000A0 is the starting point, and the confirmed drawing is the reference used for production.

How to Identify the Front and Rear Sections of a Tandem Hydraulic Gear Pump

Identify the front and rear sections separately when requesting a quote.

Use these checks before you send data, so that each section's configuration is assigned to the correct end.

Front section by drive position

The front section is the one on the shaft and flange end, and it takes drive directly from the engine or gearbox. The rear section is driven through an internal coupling, so its configuration depends on how the front section is set up.

Ports traced to circuits

Label each suction and pressure port with the circuit it feeds, such as lift and tilt, steering, or pilot. Section flows usually differ, so this tracing confirms which section carries which displacement.

Photos and measurements at teardown

Photograph the flange face, shaft end, both port faces and the full side profile next to a tape measure. Record bolt spacing, pilot diameter and port sizes. Measuring a unit that is still installed is less accurate than measuring a removed pump.

Nameplate and housing marks

Compare the nameplate text with any numbers cast or stamped on the housings and covers. If the nameplate is missing, the housing marks and measured dimensions become the main evidence, and a drawing review is required.

Fitment Checks for Foton Lovol Wheel Loaders, Including FL966H Serial-Number Confirmation

Fitment is confirmed one machine at a time. No loader model is assumed to accept this pump without these checks.

  1. Machine model and serial number

    Send the loader model and the full machine serial number. For the FL966H, the serial number must be confirmed first, because the hydraulic configuration can vary within the same model designation.

  2. Original part data

    Provide the original part number and clear nameplate photos. Part number 9G667-56B010000A0 is cross-checked against the model marking CBGJ3115/3100L.

  3. Flange and shaft

    Check the mounting flange type, bolt pattern, pilot diameter and shaft form against your measurements or drawing.

  4. Ports and rotation

    Confirm the port type, thread standard and position for each section, along with the direction of rotation viewed from the shaft end.

  5. Drawing sign-off

    We compare every item with the drawing and send the configuration back to you for written confirmation before production.

Sample, Mixed-Batch and OEM/ODM Orders for Distributors and Private-Label Buyers

Samples and mixed batches

Sample orders and mixed-batch orders are assessed per inquiry. Order quantities and delivery schedules depend on the configuration and the combination of items. A distributor might want one CBGJ3115/3100L sample alongside other gear pump models in the same shipment. We quote that as one order, with pricing set by quantity per configuration. Every item in a mixed batch still goes through the same drawing confirmation as a single-model order. This keeps a stocking order from including unverified variants.

OEM/ODM, packaging and confidentiality

For OEM/ODM projects, the process runs from your drawing or sample to an engineering review, then configuration sign-off, production against the confirmed drawing, and pre-shipment inspection. White-label units ship in neutral packaging. Custom packaging and labels can carry your brand and part references. Goods are supplied EXW Hebei, China, so you or your forwarder control freight, insurance and routing.

CBGJ3115/3100L Tandem Gear Pump FAQ for Wholesale and OEM Buyers

Can I order using part number 9G667-56B010000A0 alone?
The part number starts the quote, but production needs a confirmed configuration. We check it against your nameplate photos or drawing and send the configuration back for sign-off. This step catches differences in shaft, port or rotation before the units are built.
Why must FL966H fitment be checked by serial number?
Because the hydraulic configuration on the FL966H can differ between production runs. The full machine serial number confirms which pump configuration the loader actually uses.
Can I place a sample or mixed-batch order first?
Yes, both are assessed per inquiry. Tell us the models and the quantity of each, and we will quote the order as one shipment.
Do you offer white-label and custom packaging?
Yes. Units can ship in neutral packaging or with your brand, labels and part references printed on the cartons.
How are pumps inspected, and why EXW?
Each order is inspected against the confirmed drawing before shipment, including interfaces, markings and packaging. Goods are sold EXW Hebei, so you choose the forwarder, freight route and insurance.

Request a Quotation for the CBGJ3115/3100L Tandem Hydraulic Gear Pump

To get a configuration-matched EXW quote for your drawing review, send the following information.

Send Pump Data for a Quote

Part number 9G667-56B010000A0, plus the loader model and serial number, Nameplate photos or a drawing, Required quantity, and whether you want a sample or a mixed batch

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.