5H470-27103 5H470-27104 Hydraulic Gear Pump For Kubota DC60 688Q

1 / 4
Parameter Specification
Part numbers 5H470-27103 / 5H470-27104 (5H47027103 / 5H47027104)
Machine reference Kubota DC60 / 688Q combine harvester, serial-matched
Pump type External gear pump with side valve/fitting assembly
Housing Light silver ribbed aluminium body
Mounting and shaft Two-hole oval flange, external splined input shaft
Displacement / pressure Set from approved sample or drawing
Customization Sample matching, tooling, private-label packaging
Incoterm / origin EXW Hebei, China
MOQ Confirmed with quotation
Product Information

5H470-27103 5H470-27104 Hydraulic Gear Pump For Kubota DC60 688Q

Two reference codes, 5H470-27103 and 5H470-27104, are listed for the Kubota DC60 / 688Q combine harvester. The correct hydraulic gear pump is chosen by machine serial and pump configuration, not by part number alone.

Page 11 of the Chinese reference catalogue lists both codes under the DC60-688Q harvester. They also appear as 5H47027103 and 5H47027104. These are the same numbers written without the hyphen, not additional material numbers. The two codes should not be treated as automatically identical or as interchangeable on every machine.

We manufacture this China-supplied version in Hebei. Our sales office is in Xinji and production is in Ningjin, about 9 km apart. It is not a Kubota-branded or Kubota-supplied part. Before production, each order is matched to your machine serial, the shaft, flange and port layout, or an approved sample.

  • As pictured — Light silver ribbed aluminium body, two-hole oval front flange, external splined input shaft, black-capped ports and a side valve/fitting assembly.
  • Supply basis — Sample-based matching, tooling where required, and private-label packaging. Commercial terms are confirmed on quotation.

Send Your Machine Serial

Hydraulic Gear Pump Overview

This assembly supplies the harvester hydraulic circuit on Kubota DC60 / 688Q machines where the fitted pump carries code 5H470-27103 or 5H470-27104. Catalogue fitment is a reference only. Harvester builds vary in shaft, flange and port details, so we confirm the configuration before quoting. A serial plate photo and a few measurements are enough to rule out a pump that bolts on but does not match the drive or the hose routing.

Key Features of the 5H470-27103 / 5H470-27104 Pump

The features below are visible on the pictured unit. Any dimension behind them is taken from your sample.

  • External splined input shaft

    The pump is driven through an external spline that engages the machine drive. Tooth count and diameter are taken from your sample or drawing, not estimated from photos. A near-match spline wears quickly under harvest load.

  • Two-hole oval front flange

    The elongated flange locates the pump with two bolts. Bolt pitch and pilot diameter are checked against the removed pump before the order is confirmed.

  • Side valve and fitting assembly

    A valve/fitting block sits on the side of the body, as on the pictured unit. Its function and setting are reproduced from the approved sample. We do not assign a pressure value based on appearance.

  • Capped ports

    Ports leave the factory with black protective caps to keep contamination out during transit and storage.

Part Numbers and Technical Specifications

Use these order references and select one code by serial and configuration.

Displacement, rated pressure, speed range and rotation are fixed from the approved sample or drawing at quotation. No dimension drawing is published for this listing.

Number Written variant Role
5H470-27103 5H47027103 Kubota DC60 / 688Q harvester reference code, selected by serial
5H470-27104 5H47027104 Kubota DC60 / 688Q harvester reference code, selected by serial

Material and Construction

The pictured unit has a light silver ribbed aluminium housing. The ribs stiffen the body without the weight of a cast-iron casing. Gear sets in pumps of this class are typically hardened steel running in close-clearance bores, and those clearances largely set volumetric efficiency. The shaft seal, port threads and side valve assembly are matched part by part to the approved sample. Materials beyond the visible aluminium body are stated in the quotation rather than assumed.

How the Gear Pump Works

Two meshing gears rotate inside the housing. Oil from the inlet is carried around the outside of the gears in the tooth spaces and pushed out where the teeth re-mesh on the outlet side. Theoretical flow in L/min equals displacement in cc/rev multiplied by shaft rpm and divided by 1,000, before volumetric losses. The pump produces flow, and the load in the circuit determines pressure. The side valve/fitting block works within that circuit as on the original configuration, and its exact role is confirmed from the sample rather than inferred.

Quality Control Process

Every check refers back to the approved sample, not a generic template.

  1. Incoming material

    Castings, gears and seals are checked against the size and material records for the approved sample.

  2. Machining checks

    Spline, flange bolt holes and port positions are measured against the sample or drawing before assembly.

  3. Clean assembly

    Components are assembled clean and the ports are capped straight away. The side valve block is fitted as on the sample.

  4. Function check

    Agree the rotation, leakage and functional test requirements for the confirmed configuration before production.

  5. Release

    Part number marking and packaging are checked against the order before dispatch from Ningjin.

Where This Pump Is Used

Kubota DC60 combine harvester

Hydraulic supply on machines fitted with 5H470-27103 or 5H470-27104, subject to serial matching.

Kubota 688Q harvester

Same reference codes, with the configuration confirmed for each machine.

Harvester parts distribution

A confirmed code held for seasonal demand in rice and grain regions.

Harvest contractors

A matched spare kept on hand to limit downtime during the season.

Installation Guide

  1. Confirm the code

    Read the part number on the removed pump and the machine serial. Then choose between 5H470-27103 and 5H470-27104.

  2. Compare side by side

    Check the flange, spline, port positions and rotation against the removed pump before fitting.

  3. Clean and prime

    Replace contaminated oil and filters, then prime the pump inlet with clean hydraulic oil.

  4. Mount

    Engage the spline without force. Tighten the flange bolts evenly to the value in the machine service manual.

  5. Start-up

    Run at low idle and bleed the air. Check for leaks and abnormal noise before putting the machine under load.

Maintenance and Service Life

Oil cleanliness

Change oil and filters at the Kubota manual intervals. Contamination is the usual cause of gear and bore wear.

Suction side

Keep the inlet hoses tight and the reservoir full. Air ingress can cause aeration, noise and unstable flow.

Spline check

Inspect the shaft spline and drive coupling every time the pump is removed.

Service life

Life depends on oil cleanliness, duty hours and working pressure. No fixed hour figure is stated.

How to Choose the Right Code

  1. Identify

    Send the code on your current pump (5H470-27103 or 5H470-27104) and the machine serial.

  2. Photograph

    Send photos of the shaft end, flange, ports and side valve block with a ruler in frame.

  3. Exclude look-alikes

    Other 5H470 suffixes require separate configuration checks. The T1150 tractor pump shown on the same catalogue page is a separate family.

  4. Set volume

    Give your first-order quantity and annual volume. Distributor pricing is tiered by quantity on the quotation.

  5. Approve

    Sign off the matched specification, or a sample, before batch production starts.

OEM & ODM Customization

We duplicate the pump from your sample and can supply it under your brand.

  • Configuration matching — Shaft, flange, port and valve details are reproduced from your sample or drawing, with tooling made where required.
  • Private label — Your logo, carton print, barcode and label layout. A neutral pack is also available.
  1. Requirement

    Send a sample, a drawing or measured photos. An NDA can be signed on request before files are shared.

  2. Sampling

    A sample is built to the agreed specification. Sampling time and any tooling cost are stated on the quotation.

  3. Approval

    You test and approve the sample.

  4. Production and delivery

    The batch is built and checked against the approved sample, then packed to your label specification.

Packaging and Shipping

Port protection

All ports are capped and each pump is bagged before cartoning.

Branding

Neutral or branded cartons carry your barcode labels.

Trade terms

Supplied EXW Hebei, China. FOB or CIF can be quoted on request.

Carton data

Carton size, gross weight and units per carton are given with the quotation.

MOQ and Lead Time

MOQ

Quoted per code

Based on your first-order quantity and annual volume

Lead time

Quoted per order

Depends on whether sample matching or tooling is needed

Incoterms

EXW Hebei, China

FOB / CIF on request

Payment

Payment method confirmed in quotation

Terms agreed on the quotation

Samples

Available

Matched to your pump or drawing

Warranty and After-sales Support

Warranty terms

Coverage and duration are written into the quotation for each order.

Pre-order matching

Fitment is checked from your serial, photos and measurements before you pay for production.

Sample reference

Each batch is checked against the approved sample, which gives a fixed reference if a claim arises.

FAQ

Are 5H470-27103 and 5H470-27104 interchangeable?
Not automatically. Both are listed for the Kubota DC60 / 688Q harvester, but the correct code depends on the machine serial and pump configuration.
Is 5H47027103 a different part from 5H470-27103?
No. 5H47027103 and 5H47027104 are the same numbers written without the hyphen.
Is this an original Kubota part?
No. It is a China-manufactured version made in Hebei and matched to your machine configuration.
Can you state pressure and displacement now?
Only after matching. These values are confirmed from an approved sample or drawing, because pumps that look alike can differ inside.
Which terms can I use when asking in my own language?
Any of the following. EN: hydraulic gear pump 5H470-27103 5H470-27104. ES: bomba hidráulica de engranajes 5H470-27103 5H470-27104. PT: bomba hidráulica de engrenagens 5H470-27103 5H470-27104. RU: шестерённый гидронасос 5H470-27103 5H470-27104. AR: مضخة تروس هيدروليكية 5H470-27103 5H470-27104. TR: hidrolik dişli pompa 5H470-27103 5H470-27104. FR: pompe hydraulique à engrenages 5H470-27103 5H470-27104. VI: bơm bánh răng thủy lực 5H470-27103 5H470-27104. ID: pompa roda gigi hidrolik 5H470-27103 5H470-27104.

Get a Matched Quote or Sample for 5H470-27103 / 5H470-27104

Send us your machine serial, the code on your current pump, photos of the shaft, flange and ports, and your first-order quantity or annual volume. We will reply with the matched configuration, the quotation, a sample option and the lead time for that quantity.

Request a QuoteAsk for a Sample

You May Also Like

Related Articles

Send Your Inquiry Today

Contact us now for a professional solution and fast quote.