Шестеренные гидравлические насосы CBN300 с задним входом и передним выходом, 4,5–30 см³

1 / 3
Позиция Спецификация
Производитель Olive Branch Hydraulics
Серия CBN300 шестеренчатый одинарный наружного зацепления насос с входом сзади и выходом спереди
Рабочие объёмы 4,5; 6; 8; 10; 12; 14; 16; 18; 20; 22; 25; 28 и 30 см³/об
Монтаж Прямоугольный фланец крепления на четыре отверстия; уточнить диаметр центрирующего выступа и межцентровые расстояния болтов
Масляные порты Расположение: вход сзади, выход спереди; идентификация и размеры портов подтверждаются по заказному чертежу
Вал Показано исполнение со шлицевым валом; прочие варианты привода оценены по тому же чертежу корпуса
Давление Значения зависят от модели: см. таблицу для каждой отдельной модели; не используйте единый предел давления для всех типоразмеров
Справочная частота вращения Номинальная — 2 000 об/мин; максимальная — 3 000 об/мин, в зависимости от условий эксплуатации
Справочное направление вращения Исполнение с левым вращением по каталогу; уточните направление стрелки и направление взгляда на конец вала
Оборудование Вспомогательная гидравлика сельскохозяйственной техники и гидравлические насосные станции при подтвержденной совместимости монтажа
Номер OEM/материала Подтверждается по маркировке установленного насоса, справочным данным машины и габаритному чертежу
поделиться вFacebookXLinkedInPinterestWhatsApp
Информация о продукции

CBN300 gear pumps with rear inlet and front outlet

Olive Branch Hydraulics manufactures hydraulic gear pumps and supports OEM/ODM development for agricultural and mobile equipment. This product group brings together the CBN300 end-port arrangement and its catalogue displacement sizes in one selection guide.

The illustrated pump has a rectangular four-hole mounting flange, a splined drive shaft and connections at the end covers. Compare the front face, rear cover and complete pump marking with the installed unit when requesting a quotation. Port position is a key part of the installation specification.

Model sizes and pressure references

Catalogue model Displacement cm³/rev Rated pressure MPa Maximum pressure MPa
CBN-F304.5 4.5 20 25
CBN-F306.0 6 20 25
CBN-F308.0 8 20 25
CBN-F310.0 10 20 25
CBN-F312.0 12 20 25
CBN-F314.0 14 20 25
CBN-F316.0 16 20 25
CBN-E318.0 18 16 20
CBN-E320.0 20 16 20
CBN-D322.0 22 12.5 16
CBN-D325.0 25 12.5 16
CBN-C328.0 28 10 12.5
CBN-C330.0 30 10 12.5

The ratings above are catalogue references for their individual model rows. Final operating limits are confirmed in the approved supply specification. Maximum pressure is not a continuous operating rating. Different displacements may require different body lengths even when grouped under the same mounting and port arrangement.

Model names and abbreviated search spellings

Catalogue designation Short spelling Spacing / punctuation search forms
CBN-F304.5 CBN-F304.5 CBNF304.5; CBN F304.5
CBN-F306.0 CBN-F306 CBNF306; CBN F306
CBN-F308.0 CBN-F308 CBNF308; CBN F308
CBN-F310.0 CBN-F310 CBNF310; CBN F310
CBN-F312.0 CBN-F312 CBNF312; CBN F312
CBN-F314.0 CBN-F314 CBNF314; CBN F314
CBN-F316.0 CBN-F316 CBNF316; CBN F316
CBN-E318.0 CBN-E318 CBNE318; CBN E318
CBN-E320.0 CBN-E320 CBNE320; CBN E320
CBN-D322.0 CBN-D322 CBND322; CBN D322
CBN-D325.0 CBN-D325 CBND325; CBN D325
CBN-C328.0 CBN-C328 CBNC328; CBN C328
CBN-C330.0 CBN-C330 CBNC330; CBN C330

The shortened and punctuation-free forms help identify an enquiry; they are not additional certified assembly numbers. For example, CBN-E318.0, CBN-E318, CBNE318 and CBN E318 may be used to describe a requested size, but the shaft, mounting, connections and rotation still need confirmation.

Series-level names include CBN300, CBN-300, CBN3 and CBN-3. Chinese product descriptions include CBN后进前出齿轮泵、CBN前后端盖油口齿轮泵、CBN方形法兰液压油泵 and 农机液压齿轮泵. English enquiry terms include rear-inlet front-outlet gear pump, CBN end-port hydraulic pump and agricultural auxiliary hydraulic oil pump.

Drive shaft options within the same body style

The confirmed images show a splined shaft. Provide its tooth count, major and minor diameters, engagement length and mating coupling information. Keyed, flat-end or other drive enquiries can be evaluated from a sample or drawing and remain within this product group after technical confirmation.

Plain key shaft, straight keyed shaft and 平键轴 describe a keyed connection. Splined shaft, spline drive and 花键轴 describe a splined connection. Flat-end shaft, tang drive and 扁口轴 describe a flat drive connection requiring dimensional approval. These names do not by themselves establish that two drive connections are interchangeable.

Confirm the installation before production

Measure the locating pilot, mounting-hole centres, flange thickness and available clearance. Record the oil-port thread or flange dimensions and the position of the hydraulic lines. Check the rotation arrow and viewing direction from the shaft end; a photograph alone is not enough to confirm the required rotation.

Send the continuous and peak working pressures, speed range, oil type, temperature and duty cycle. For a first flow estimate, multiply displacement in cm³/rev by shaft speed and divide by 1,000 to obtain theoretical litres per minute. Actual delivery depends on leakage and operating conditions.

Equipment identification and OEM/ODM enquiries

This group can be assessed for tractor and harvester auxiliary hydraulic circuits and agricultural hydraulic power units. A machine brand, model or OEM material number is confirmed from the original pump identification and technical evidence for each enquiry.

For sample-based manufacture, provide an original unit or a complete dimensional drawing together with the required quantity. We will evaluate the body, drive shaft, mounting and oil connections, then agree the technical specification, inspection requirements, identification and export packing.

The three product reference images show the approved overall view, rear connection and front mounting face. They are not independent photographs of all thirteen displacement sizes. The approved order drawing defines the final supplied configuration.

Frequently asked questions

Why are F, E, D and C models listed together?

They appear in the reviewed catalogue group for this end-port arrangement, with different pressure references. Keep each complete model and its individual rating when specifying the required pump.

Can I order a pump from a size number alone?

Provide the full marking, shaft details, mounting dimensions, port arrangement and rotation so that the correct execution can be confirmed.

Can different shafts be supplied in one order?

Yes, subject to technical confirmation for each execution. State the shaft details and quantity separately within the same product group.

Вам также может понравиться

Похожие статьи

Отправьте ваш запрос сегодня

Свяжитесь с нами прямо сейчас для получения профессионального решения и быстрого расчёта стоимости.