69101-GG00A Nissan Forklift Hydraulic Gear Pump

1 / 4
Parameter Specification
Pump type External gear pump, aftermarket replacement
Reference code 69101-GG00A (identification only)
Compatibility basis Complete assembly code, forklift model, equipment details
Interfaces matched Mounting flange, shaft end, rotation, P/T ports
Customization Custom P/T port configurations, OEM drawings
Inspection 100% final inspection before packaging
MOQ (stocked models) 1 piece
Lead time (stocked models) 3–5 business days
Warranty One year, terms in written quotation
Incoterms EXW Hebei, China
поделиться вFacebookXLinkedInPinterestWhatsApp
Информация о продукции

Nissan Forklift Hydraulic Pump 69101-GG00A Replacement Gear Pump

A Nissan forklift hydraulic pump 69101-GG00A replacement fits your truck when the complete assembly code, mounting flange, shaft end, rotation and P/T ports all match the pump you are removing.

The part number is where matching starts, but it does not settle it. Trucks from different production years can carry gear pumps under the same reference that differ in shaft spline, port thread or section layout. We match every 69101-GG00A replacement pump against three things: the original code, the forklift model and the equipment details you send. When all three agree, the pump fits the existing drive housing and connects to the existing hoses without adapters.

On counterbalance forklifts the main gear pump typically feeds the control valve for lift and tilt. On many models it also supplies the steering circuit through a priority valve. A worn pump usually shows up as slow lift under load, weak tilt and louder pump noise once the oil is hot. Before ordering, workshops and parts distributors should confirm the interface details below, because a pump that looks similar but differs at the flange or ports leads to rework on the truck.

How the 69101-GG00A Forklift Gear Pump Turns Engine Drive into Lift and Tilt Pressure

Suction and discharge in an external gear pump

Two meshing gears turn inside a close-fitting housing, driven from the engine. On the inlet side the teeth separate, the trapped volume expands and oil is drawn from the tank. Oil then travels in the tooth spaces around the housing wall to the outlet. There the re-meshing teeth push it into the pressure line that feeds the lift and tilt cylinders through the control valve. Displacement per revolution is fixed, so flow follows engine speed. This is why lift speed rises as the operator increases throttle.

Clearances, side plates and internal leakage

Volumetric efficiency depends on two gaps: between the gear tips and the housing, and between the gear faces and the side plates or bushings. Many forklift gear pumps use pressure-balanced plates that load against the gear faces as outlet pressure rises, which limits axial leakage under load. Scored housings, worn bushings or a hardened shaft seal let oil slip back to suction. The result is a pump that lifts normally when empty and slows with a full pallet, especially with hot oil at low engine speed. A replacement with different bushing design or housing clearances will behave differently in exactly those conditions.

Why Mounting Flange, Shaft and Port Layout Decide Whether a Nissan Forklift Pump Swap Succeeds

The interfaces that must match the original

Matching the displacement is not enough if the interfaces differ. The flange pilot diameter and bolt pattern locate the pump on the drive housing. The shaft form, whether splined or keyed, must engage the existing drive coupling. Rotation direction determines which port is suction, and a pump run in the wrong direction quickly starves and damages its seals. Port position and thread standard (BSP, metric or SAE O-ring boss are common on forklift pumps) decide whether the original hoses connect directly. If they do not match, you face adapters, rerouted lines and an added leak point.

How replacement matching works

Send us the original code 69101-GG00A, the forklift model and the equipment details, such as engine type and mast configuration. We check these against the complete assembly code and confirm flange, shaft, rotation and P/T ports before quoting. The Nissan name and 69101-GG00A are used for replacement identification only. This is an aftermarket pump, not a Nissan-supplied part, and compatibility is determined by the complete assembly code rather than the reference number alone.

Confirm the complete assembly code and all four interfaces before ordering. The reference number alone does not confirm fit.

69101-GG00A Replacement Data: Codes, Interfaces and Assembly Details to Confirm

These are the details we need to confirm a matched replacement.

OEM reference and assembly code

69101-GG00A identifies the application. The complete assembly code on the pump label or body separates variants. If the plate is unreadable, send clear photos of the pump body and both ports instead.

Forklift model and equipment details

Include the truck model, engine type, mast configuration and approximate build year. These details narrow down variants that share the same reference number.

Mounting interface and shaft end

We need the flange type, bolt pattern, pilot diameter and spline or key details. If the documentation is incomplete, caliper measurements taken from the old pump are accepted.

Port configuration and rotation

Specify the P/T port positions, thread standard and size, and the rotation as viewed from the shaft end. Distributor-specific port layouts are fixed on the approved drawing.

Performance data

Displacement, pressure and flow are confirmed on the sample or the approved drawing, not taken from a general catalogue. For this reason, no figures are listed here.

Where Nissan Forklift Hydraulic Pump Replacements Are Needed: Warehouses, Logistics Hubs and Plants

Forklift maintenance and repair

Service shops need a pump that fits the first time, so the truck goes back into service within one visit.

Warehouse material handling

Shift operators need lift speed under load to return to normal, so racking work is not slowed.

Logistics and distribution centers

Fleet managers need short dispatch times, so trucks are not parked during peak periods.

Forklift parts distribution

Distributors need consistent interfaces across batches and predictable restocking.

Manufacturing plant operations

Plant maintenance teams need a direct swap without modifying hoses or brackets on internal transport trucks.

From Drawing to Batch: Building Custom-Port 69101-GG00A Pumps for Distributors

OEM and aftermarket custom orders, including distributor-specific P/T port configurations, follow six steps.

Production runs at our manufacturing partner in Ningjin, established in August 2010 and about 9 km from the Xinji sales office.

  1. Inquiry

    You send the code, forklift model, port requirements and quantity. We confirm the complete assembly code and the interface data.

  2. Design drafts and 3D renders

    We prepare drawings and renders showing section order, port positions and mounting interfaces. You review these before any sample is made.

  3. Drawing approval and sampling

    Samples are built only after you approve the drawing. That drawing becomes the inspection reference for every later batch.

  4. Production with in-process QC

    Parts are checked during machining and assembly against the approved drawing, not against a general catalogue specification.

  5. 100% final inspection

    Every pump is inspected before packaging. Any deviation from the drawing is resolved before the batch ships, not after it arrives.

  6. Packaging and dispatch

    Ports are sealed, units are packed and the goods are handed over for shipment to your destination port.

1-Piece MOQ, 3–5 Day Dispatch and Tiered Pricing for 69101-GG00A Bulk Orders

  • Stocked units

    The MOQ is 1 piece and orders ship within 3–5 business days. This suits urgent repairs and trial orders before a distributor commits to stock.

  • Custom and OEM orders

    MOQ and lead time depend on the configuration and the order quantity. Each stage, from drawing approval through to repeat production, has its lead time confirmed in the written quotation.

  • Tooling fee refund

    If tooling is required, the fee is refunded in full once your cumulative purchases of that model reach the agreed quantity. Multiple orders count toward that total.

  • Written tiered quotation

    The quotation lists unit prices by quantity, the tooling fee, the refund quantity, warranty terms and EXW Hebei, China delivery. Payment terms are also confirmed in writing.

Warranty, Inspection Items and Documents: What Parts Buyers Ask About the 69101-GG00A

What warranty applies to the 69101-GG00A replacement pump?
One year. The coverage terms are stated in the written quotation.
Which inspections can be performed on my order?
Dimensional checks, leak inspection and, where applicable, pressure and flow testing. The scope is agreed in the quotation and checked against your approved drawing.
What documents ship with the goods?
The required documents are agreed in the quotation before production. Tell us what your customs process or your customers require.
Are third-party test reports or certificates your certifications?
No. Third-party document references belong to their holders and are not Olive Branch Hydraulics certifications.

Price Your 69101-GG00A Pump Order: Send the Code, Forklift Model and Destination Port

Send us the code 69101-GG00A, your forklift model and equipment details, the quantity and your destination port. You will receive a matching confirmation and a written quotation within 24 hours. Email [email protected] or call +8615075996564.

Request a 69101-GG00A Quotation

Вам также может понравиться

Похожие статьи

Отправьте ваш запрос сегодня

Свяжитесь с нами прямо сейчас для получения профессионального решения и быстрого расчёта стоимости.