SGP2 Forklift Hydraulic Gear Pump

1 / 2
Parameter Specification
Pump type Fixed-displacement external gear pump
Mounting (reference version) SAE B two-bolt flange, SAE J744
Rotation CW or CCW viewed from shaft end, confirmed per order
Displacement, pressure, speed Per full assembly code, verified against sample or drawing
Shaft and ports Spline and port layout matched to approved drawing
Customization P/T port configuration, marking, packaging
Inspection 100% final inspection; leak and pressure/flow test where applicable
Incoterms EXW Hebei, China
Quotation response Within 24 hours of receiving code, quantity, port

SGP2 External Gear Pump — Catalogue Reference

Mounting flange SAE B two-bolt
Drive shaft Splined. Confirm tooth count, pitch and shaft length.
Rotation Counterclockwise viewed from the shaft end for the listed reference configuration.
Displacement, rated pressure and speed Confirm with the full assembly code or original drawing.
Inlet and outlet Confirm size, thread and position on the original pump.

The catalogue also mentions Fermec 860, 960 and 965. Confirm machine serial number and original pump part number before ordering for these machines.

SGP2 Forklift Steering Pump — Ordering Checks

The steering-pump catalogue entry lists an SAE B two-bolt flange, a splined shaft and counterclockwise rotation when viewed from the shaft end. Confirm the full assembly code before ordering, including the spline tooth count, shaft engagement length and port position.

Check whether the truck uses a dedicated steering pump or a shared pump feeding a priority valve. Match the original circuit and confirm displacement, pressure and speed against the pump drawing or service data.

Produktinformationen

SGP2 Forklift Hydraulic Gear Pump with SAE B Two-Bolt Flange

A replacement SGP2 forklift hydraulic gear pump fits your truck only when its full assembly code matches the original. The series name alone is not enough, because SGP2 units with the same frame can differ in displacement, rotation, shaft spline and port layout.

The SGP2 is a fixed-displacement external gear pump. On forklifts it typically feeds the lift and tilt circuits and, on many trucks, the power steering priority valve. The reference version of this pump specifies an SAE B two-bolt mounting flange. Before quoting, we confirm the complete assembly code, rotation viewed from the shaft end, displacement, pressure, speed, spline, flange dimensions and port layout against your sample or drawing.

This check matters most for distributors who stock replacements for several truck brands, and for maintenance teams replacing a failed pump on a running fleet. A pump that bolts on but turns the wrong way, or has its pressure port on the wrong side, comes back as a return and costs downtime. Brand names and part numbers on this page are for replacement identification only.

  • Mounting reference — The reference version uses an SAE B two-bolt flange. Pilot and bolt spacing are checked against your sample or drawing before quoting.
  • Matching inputs — Matching starts from the original product code, the machine model and the equipment details. Drawings or the old pump can be used to confirm features the code does not show.
  • Approval before sampling — Design drafts and 3D renders are sent to you for approval before any sample is built.
  • Final inspection — Every pump goes through final inspection before packaging. Leak checks and pressure/flow testing are included where applicable.
Application engineering

What Determines SGP2 Gear Pump Interchangeability

The short answer

Two SGP2 pumps can look identical on the bench and still be wrong for your truck.

Why the series name is not a part number

SGP2 identifies a pump frame size, not a single configuration. Within one frame, manufacturers vary the gear width to change displacement, offer clockwise and counter-clockwise versions, and fit different shaft and port options for each truck model. The complete assembly code records these choices, which is why we quote against the full code and not the series name. If the nameplate is worn or missing, the old pump or the truck's equipment data fills the gap.

Rotation, viewed from the shaft end

Rotation is always stated as seen when facing the drive shaft. A gear pump run in the wrong direction moves its suction to the pressure side. Depending on the seal and bushing design, the shaft seal can fail within minutes. Many ordering mistakes come from reading rotation from the port end or from the engine side, so we confirm the direction against your sample or drawing and do not rely on an assumed convention.

Flange, spline and ports as one fit

The SAE B two-bolt flange on the reference version follows the SAE J744 family. That standard sets a nominal 101.6 mm (4.00 in) pilot and a 146 mm (5.75 in) bolt spacing. The shaft spline must engage the drive coupling or PTO without forcing, and SAE B pumps commonly use a 13-tooth 16/32 DP spline, though variants exist. Port position, size and thread type decide whether your existing hoses connect without adapters. We check all three together because each can be right on its own while the assembly still fails to fit.

Displacement, rated pressure, speed, spline, flange and ports are confirmed against your sample or drawing before quoting. We do not assume them from the series name.

SGP2 Forklift Gear Pump Technical Specifications

The values marked "per assembly code" vary by truck model and are confirmed for each order. They are not fixed for the series.

Pump type

Fixed-displacement external gear pump

Typical forklift circuits

Lift, tilt and power steering supply

Mounting (reference version)

SAE B two-bolt flange, SAE J744

Pilot diameter (SAE B nominal)

101.6 mm (4.00 in)

Bolt spacing (SAE B two-bolt nominal)

146 mm (5.75 in)

Shaft

Spline per assembly code; SAE B commonly 13T 16/32 DP

Rotation

CW or CCW, viewed from shaft end; confirmed per order

Displacement

Per assembly code; verified against nameplate, sample or drawing

Rated pressure and speed

Per assembly code and original equipment data

Ports

Position, size and thread matched to drawing; custom P/T layouts available

Section arrangement

Single or multi-section; section order verified against approved drawing

Testing

Dimensional check, leak inspection, pressure/flow test where applicable

Not sure which SGP2 variant is on your truck?Send the code stamped on the pump body, the truck make and model, and a photo of the shaft end and ports. We confirm the match before you place an order.

Check my pump code

How to Specify a Replacement Forklift Hydraulic Gear Pump

Four inputs settle most SGP2 replacement orders.

Assembly code and machine model

Start with the full code from the original nameplate, including any suffix letters. Then add the forklift make, model and serial range, because one truck model can use different pumps across production years. If you supply several truck brands, list every original code you need covered. Codes that share a frame and differ only in port layout can then be grouped for quotation.

Displacement, pressure and speed

Displacement sets the lift and tilt speed at a given engine or motor rpm. A larger pump also draws more input torque. On LPG and diesel trucks the pump runs at engine speed, while on electric trucks it runs at the hydraulic motor speed. Confirm the original rated pressure as well, because the relief valve setting on the truck should not exceed the pump's rating.

Physical fit

Measure, or let us measure, the flange pilot and bolt spacing, the spline tooth count and pitch, the shaft length, and the inlet and outlet positions. Where an original drawing exists, we check against it. Where it does not, the old pump or a sample serves as the reference.

Send these with your request

  • Full assembly code from the nameplate
  • Forklift make, model and engine or motor type
  • Rotation as seen from the shaft end
  • Photos of the shaft, flange and ports, or a drawing

Information that is not enough on its own

  • Series name only, such as "SGP2"
  • Truck brand without the model or year
  • Rotation viewed from the port end or the engine

Custom and OEM SGP2 Gear Pumps

Custom pumps are built to an approved drawing, and quality checks are tied to that drawing and not to a general catalogue specification.

Olive Branch Hydraulics sells from Xinji, Hebei. Production is done with a manufacturing partner in Ningjin, about 9 km from the sales office. This makes it practical to verify samples and batches at the production site before shipment.

Port configuration

Pressure and tank port positions, sizes and threads can be changed. This lets distributors cover several truck models with fewer SKUs.

Mounting and shaft

The flange and spline are matched to your drawing or sample. The SAE B two-bolt version is the reference build.

Section arrangement

Section order, port positions and mounting interfaces are checked against the approved drawing. Any deviation is resolved before the batch ships, not after it arrives.

Marking and packaging

Nameplate content and carton labelling can follow your part numbering. Third-party brand marks are used only for replacement identification.

How custom orders work

  1. Inquiry

    You send the code, drawing or sample, the quantity and the destination port.

  2. Design

    We send drafts and 3D renders for your approval before any sample is made.

  3. Sampling

    A sample is built to the approved drawing for your fit and function test.

  4. Production

    Batch production runs with in-process quality control, followed by 100% final inspection.

  5. Packing and shipping

    Pumps are packed and handed over EXW for your forwarder, or shipped to your nominated port as agreed.

Pricing, MOQ and Trade Terms

All commercial terms are fixed in one written quotation, so you can compare it directly with other offers.

Pricing Tiered unit price by quantity · Price breaks are listed in the quotation, which helps when you plan distributor margins.
MOQ and lead time Stated in the written quotation · Both depend on the confirmed configuration and quantity, and are fixed before tooling begins.
Tooling fee Fully refunded at an agreed cumulative quantity · Quantities from repeat orders of the same model count toward the total.
Incoterms EXW Hebei, China · Goods are handed over at the manufacturer's facility. Payment terms are confirmed in the quotation.
Inspection and documents Agreed in the quotation · The quotation covers dimensional checks, leak inspection and pressure/flow testing where applicable.
Warranty Terms stated in the written quotation · Coverage applies to the configuration you approved.

SGP2 Forklift Hydraulic Gear Pump FAQ

Can you match a pump when the nameplate is unreadable?

Yes, provided we have the old pump, a drawing or full photos plus the truck model. We work from the flange, spline, port layout and gear section dimensions to identify the configuration. Displacement and rotation are confirmed with you before quoting.

Will an SGP2 replacement accept my existing hoses and fittings?

Yes, when the port positions, sizes and thread types match the original. These are part of the drawing check. If you want a different port layout to suit your stock, we can build to that instead.

Are the brand names and part numbers on this page original parts?

No. Brand names and model numbers are used only to identify the correct replacement. Compatibility depends on the complete assembly code, and any third-party document references belong to their holders.

Can I send a used pump for measurement?

Yes. A used or failed pump is a valid reference for flange, spline, port and section measurements. Tell us before shipping so we can confirm the receiving address and what you need checked.

What packing do pumps usually ship in?

Gear pumps are typically shipped with plugged ports and a protected shaft. They are sealed in anti-rust film and packed in individual cartons, with multiple units palletised or crated for sea freight. The exact packing is confirmed in the quotation.

Send Your Pump Code or a Sample for Matching

Send the full assembly code, the forklift model, the quantity and your destination port to [email protected]. You will get a configuration check and a written EXW quotation within 24 hours. If you would rather test before ordering, send the old pump or a drawing, and we will confirm the sample arrangement in the quotation.

Request a quotationArrange a sample

  • Full code or nameplate photo
  • Rotation viewed from the shaft end
  • Quantity and destination port

Das könnte Ihnen auch gefallen

Verwandte Artikel

Senden Sie Ihre Anfrage noch heute

Kontaktieren Sie uns jetzt für eine professionelle Lösung und ein schnelles Angebot.